Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When CONFIG_SYS_FSL_ERRATUM_A009801 is defined but
CONFIG_SYS_FSL_ERRATUM_A008511 not defined, there is compile error
that temp32 undeclared, this patch fixes it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DDR controller 5.2.1 has this erratum A008511 partially fixed.
The workaround needs to be adjusted to take advantage of Vref
training. This patch enables the training and force output
enable to be off.
Erratum A009803 requires the controller to be idel before enabling
address parity. It was combined with workaround for A008511. With
new A008511 flow, this flow needs to be changed to enabling
data init (D_INIT) after the address parity is enabled.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
32 more debug registers are added for newer DDR controllers.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
Add condition of checking the enabled of address parity
for erratum A-009803, if parity is not enabled, the
workaround of erratum A-009803 should not be applied.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.
Signed-off-by: York Sun <york.sun@nxp.com>
The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Per the latest erratum document, update step 4 and step 8, only
DEBUG_29[21] is changed, all other bits should not be changed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Minor change: chosen is written with one "o".
No code change here, only comment & printf.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Following commit 61bd2f75, exclude unused DDR controller from
calculating RAM size for SPL boot.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.
Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.
Signed-off-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
By default the bstopre value has been set to 0x100, used to be 1/4
value of refint. Modern DDR has increased the refresh time. Adjust
to 1/4 of refresh interval dynamically. Individual board can still
override this value in board ddr file, or to use auto-precharge.
Signed-off-by: York Sun <yorksun@freescale.com>
In case SPD address changes between board revisions, updating SPD
address can be called from board file.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.
Signed-off-by: York Sun <yorksun@freescale.com>
CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.
Signed-off-by: York Sun <yorksun@freescale.com>
Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.
Signed-off-by: York Sun <yorksun@freescale.com>
According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.
>From section 9.4.1.8 of that manual:
Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.
0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.
In addition, Freescale application note AN2805 is also very clear that
this bit must be set.
This patch reverts a change introduced by commit
457caecdbc.
Testing Done:
Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:
fff9b774: 65 29 80 00 oris r9,r9,32768
Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.
Booted an image on a MPC8541 based board successfully.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add sync of refresh for multiple DDR controllers. DDRC initialization
needs to complete first. Code is re-ordered to keep refresh close.
Signed-off-by: York Sun <yorksun@freescale.com>
Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.
Signed-off-by: York Sun <yorksun@freescale.com>
On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.
These should be set before MEM_EN is set.
Signed-off-by: York Sun <yorksun@freescale.com>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.
DDR4 is not affected by this change.
Signed-off-by: York Sun <yorksun@freescale.com>
York Sun
Masahiro Yamada
Shaohui Xie
Shengzhou Liu
Robert P. J. Day
Alexander Merkle
Ed Swarthout
Shengzhou Liu
Tom Rini
Yao Yuan
York Sun
Prabhakar Kushwaha
Joakim Tjernlund
York Sun
Curt Brune