Add a new 'demo light' command which uses GPIOs to control imaginary lights.
Each light is assigned a bit number in the overall value. This provides an
example driver for using the new GPIO API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a deprecation notice to each function so that it is more obvious that we
are moving GPIOs to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present U-Boot sort-of supports the standard way of reading GPIOs from
device tree nodes, but the support is incomplete, a bit clunky and only
works for GPIO bindings where #gpio-cells is 2.
Add new functions to request GPIOs, taking full account of the device
tree binding. These permit requesting a GPIO with a simple call like:
gpio_request_by_name(dev, "cd-gpios", 0, &desc, GPIOD_IS_IN);
This will request the GPIO, looking at the device's node which might be
this, for example:
cd-gpios = <&gpio TEGRA_GPIO(B, 3) GPIO_ACTIVE_LOW>;
The GPIO will be set to input mode in this case and polarity will be
honoured by the GPIO calls.
It is also possible to request and free a list of GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Only the GPIO driver knows about the full GPIO device tree binding used by
a device. Add a method to allow the driver to provide this information to the
uclass, including the GPIO offset within the device and flags such as the
polarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far driver model's GPIO uclass just implements the existing GPIO API.
This has some limitations:
- it requires manual device tree munging to support GPIOs in device tree
(fdtdec_get_gpio() and friends)
- it does not understand polarity
- it is somewhat slower since we must scan for the GPIO device each time
- Global GPIO numbering can change if other GPIO drivers are probed
- it requires extra steps to set the GPIO direction and value
The new functions have a dm_ prefix where necessary to avoid name conflicts
but we can remove that when it is no-longer needed. The new struct gpio_desc
holds all required information about the GPIO. For now this is intended to
be stored by the client requesting the GPIO, but in future it might be
brought into the uclass in some way.
With these changes the old GPIO API still works, and uses the driver model
API underneath.
Signed-off-by: Simon Glass <sjg@chromium.org>
For GPIOs and other functions we want to look up a phandle and then decode
a list of arguments for that phandle. Each phandle can have a different
number of arguments, specified by a property in the target node. This is
the "#gpio-cells" property for GPIOs.
Add a function to provide this feature, taken modified from Linux 3.18.
Signed-off-by: Simon Glass <sjg@chromium.org>
The common/board_r.c has show_model_r() to display the model name
if the DTB has a "model" property. It sounds useful to have a similar
function in common/board_f.c too because most of the boards show
their board name before relocation.
Instead of implementing the same function in both common/board_f.c
and common/board_r.c, let's split it up into common/show_board_info.c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
updated the zynq config to support the lthor
download protocol.
This lthor functionality helps us to load linux
images on to DDR/MMC and can boot linux using bootm.
In order to load images the user should run lthor
command run "thor_ram" from u-boot prompt and
then send the images from host using lthor utility.
Define g_dnl_bind_fixup for zynq so that correct vendor
and product ids assigned incase of DFU and lthor.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable DFU functionality in zynq.
This DFU functionality helps us to load linux
images on to DDR and can boot linux using bootm.
In order to load images the user should run dfu
command "dfu 0 ram 0" from u-boot prompt and then
send the images from host.
The malloc size has been increased to match the DFU
buffer requirements.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont send always emio value as zero for zynq_gem_initialize
send it based on config.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Based on:
"am335x_evm: Enable CMD_EXT4 and CMD_FS_GENERIC, add bootpart to env"
(sha1: 73a27a84e5)
Fix filesystem specific commands for loading.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add deep sleep support on Freescale LS1021QDS platform.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
As a temporary measure before the ICH driver moves over to driver model,
add device tree support to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 we use CMOS RAM to read and write some settings. Add basic support
for this, including access to registers 128-255.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the checksum code out into its own file so it can be used elsewhere.
Also use a new version which supports a length which is not a multiple of
2 and add a new function to add two checksums.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add this to the enum so that we can use the various fdtdec functions. A
later commit will move this driver to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021AQDS board.
For ls1021aqds_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the CH7301 HDMI options and the common configuration
for DCU on LS1021AQDS board.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Cc: Jason Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
Scrolling a line at a time is very slow for reasons that I don't understand.
It seems to take about 100ms to copy 4MB of RAM in the frame buffer. To cope
with this, scroll 5 lines each time.
Signed-off-by: Simon Glass <sjg@chromium.org>
We shouldn't assume that the VGA ROM can always be loaded at c0000. This
is only true on x86 machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
The CPU info is already logged during boot e.g.
CPU: Allwinner A20 (SUN7I)
so the prompt is just one more thing to change for each new SoC, just makes it
"sunxi#" instead.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The file, originally named "include/video/mipi_display.h", is taken from
linux 3.18 (commit b2776bf7149bddd1f4161f14f79520f17fc1d71d).
It provides MIPI DSI constants for DCS commands, which are needed to
implement support for SSD2828 in u-boot.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And also add Kconfig option for selecting ELDO3 voltage. The reason
for having this option is that the Android kernel sets ELDO3 to
1.2V when powering up LCD in the case if 'lcd_if' configuration
variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely
to supply power for a SSD2828 chip.
However on the MSI Primo81 tablet, which is using this particular
'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to
be unnecessary and it works regardless. Having no schematics of
this tablet, I can only guess that 1.2V is supplied to SSD2828
in some other way.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2 recent sunxi changes have removed the usage of lowlevel_init by moving some
code around and then setting CONFIG_SKIP_LOWLEVEL_INIT.
This is problematic for 2 reasons:
1) It does not just stop s_init from being called, it also stops
cpu_init_cp15 from getting called, which is undesirable.
2) We want u-boot.bin to be usable standalone, without SPL, some people e.g.
use an upstream u-boot.bin together with Allwinner's boot0 loader. So
u-boot.bin must (re)initialize the gpios, timer, etc.
This commit restores the lowlevel_init / s_init usage, while keeping the
changes to no longer use the global-data (gd) struct in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass
Masahiro Yamada
Siva Durga Prasad Paladugu
Michal Simek
Gerald Kerma
Luka Perkov
tang yuantian
Alison Wang
Xiubo Li
York Sun
Ian Campbell
Hans de Goede
Siarhei Siamashka