Use device-tree fixup to communicate the MTD partitions to the
kernel. U-Boot's mtdparts environment variable will be used as
partition source for the device-tree based partition table too.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The config block support currently uses the ft_board_setup function
to patch the device tree with config block information. However, this
does not allow to patch the device tree with board specific information.
Rename the common setup function to ft_common_board_setup and use the
call it from the board files directly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Newly add ARMv8 PSCI needs to be initialized, be copied or reserved in right
place, this patch does all the setup steps.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch introduces a generic ARMv8 PSCI framework, with all functions
returning a dummy ARM_PSCI_RET_NI (Not Implemented), then it is up to each
platform to implement their own functions based on this framework.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PSCI implementation needs the SMC instruction to be enabled.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to
hold PSCI text and data, and it is based on the legacy implementation of ARMv7.
ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and
ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here
in Kconfig too.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080A SoC family has QBMAN ver 4.0 whereas newer
SoCs like LS2088A, LS1088A has QBMAN ver 4.1
QBMAN ver 4.0 and ver 4.1 supports dqrr size as 4 and 8 respectively.
Add support of
to check QBMAN version based on SoC SVR
update dqrr_size accordingly
update code to support larger dqrr_size
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The unit-address should be the same as the I2C address of the device.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable ERRATUM_A009942 workaround for B-series and T-series platforms.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This reverts commit c56ae7519f.
Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.
Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.
Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.
Indeed the SPI controller driver is not aware of the SPI protocol switch.
Further patches will fix the support of Micron QSPI memories.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Move the code to read the "sram-size" property into the other code
that reads properties from the node, rather than the SF subnode.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Cadence QSPI controller has specified overheads for the various CS
times that are in addition to those programmed in to the Device Delay
register. The overheads are different for the delays.
In addition, the existing code does not handle the case when the delay
is less than a SCLK period.
This change accurately calculates the additional delays in Ref clocks.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of extracting mode settings and passing them as separate
args to another function, just pass the SPI mode as an arg.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A lot of the #defines are for single bits in a register, where the
name has _MASK on the end. Since this can be used for both a mask
and the value, remove _MASK from them.
Whilst doing so, also remove the unnecessary brackets around the
constants.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Most of the code already uses #defines for the bit value, rather
than the shift required to get the value. This changes the remaining
code over.
Whislt at it, fix the names of the "Rd Data Capture" register defs.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Show what the output clock rate actually is.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With the existing code, when the requested SPI clock rate is near
to the lowest that can be achieved by the hardware (max divider
of the ref clock is 32), the generated clock rate is wrong.
For example, with a 50MHz ref clock, when asked for anything less
than a 1.5MHz SPI clock, the code sets up the divider to generate
25MHz.
This change fixes the calculation.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Or'ing together bit positions is clearly wrong.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
At present an invalid bus width prints a message but does not return an
error. This is the opposite of the correct behaviour. Adjust it to avoid
code bloat in the common case, and avoid hard-to-debug failure in the
uncommon case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Unlike Linux kernel, U-Boot depends on "spi-flash" compatible to probe
m25p80 spi-nor devices. Hence, add "spi-flash" compatible string to
m25p80 node. Without this patch, flash device DT data is not parsed and
QSPI operates in unsupported mode leading to data corruption.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since I leave Samsung by the end of the year, I will not have access to
OneNAND devices anymore.
Hence the custodian position has been marked as "Orphaned".
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Enable hush parser in Armada-7040 and Armada-8040 DB default
configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable PCIe bus support in Armada-7040 DB default configuration
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add missing L3 cache flush functionality which absence prevents
Linux kernel from normal boot in case the L3 cache is enabled
by ATF.
The L3 cache is named the "last level" cache in order to keep
the terminology similar to the ATF code.
This cache should not be disabled by u-boot since the Linux
kernel cannot activate it, so it is activates at ATF stage.
However the cache flush is required for preventing data corruption
after disabling the MMU and the data cache before passing control
to the loaded Linux image.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable mvebu pin control support in the default configuration
files for Armada-7040 and Armada-8040 development boards
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable mvebu "bubt" command support in the default configuration
file for Armada-7040 and Armada-8040 development boards
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for mvebu bubt command for flash image
load, check and burn on boot device.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Align the Armada-8040-db and Armada-7040-db SPI and I2C
DTS settings with latest DB settings:
- 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO)
- 8040-db: disable cps_i2c0 on CP1
- 8040-db: enable spi1 on CP1 (the new location of the boot flash)
The spi1 on CP1 is aliased as spi0 since this is the way
the driver enumerates it.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a user configurable option, but "select BLK" forces users to
enable it.
Even with this commit, BLK is still enabled by "default y if DM_MMC"
for UniPhier SoCs; the difference is users can disable it if they
do not need it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not overwrite the memory nodes in the kernel DT where some parts
of the memory region might be carved out.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stefan Agner
Stefano Babic
macro.wave.z@gmail.com
Priyanka Jain
Hou Zhiqiang
Shengzhou Liu
Cyrille Pitchen
Phil Edworthy
Fabien Parent
Simon Glass
Vignesh R
Michal Simek
Lukasz Majewski
Tom Rini
Konstantin Porotchkin
Masahiro Yamada
Jyri Sarha
Christian Riesch