A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is a workaround for hardware erratum.
Write the value of 63b2_0042h to EDDRTQCFG will optimal the
memory controller performance.
The value: 63b2_0042h comes from the hardware team.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable the IP feature's snoop signal to support
hardware snoop for cache coherence.
SNPCNFGCR contains the bits to drive snoop signal
for various masters.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Create a soc.c file to put the code for soc special settings.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot. Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value. This causes the timer compare to fire 344 seconds
after u-boot configures it. Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable snooping for CAAM read & write transactions by
programming the SCFG snoop configuration register:
SCFG_SNPCNFGCR[SECRDSNP]
SCFG_SNPCNFGCR[SECWRSNP]
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ISBC Key Extension feature is not applicable for RAMBOOT
as there is no way to retrieve the CSF Header and validated
IE Key table from SRAM once CPC has been disabled.
The feature is only applicable in case of NOR SECURE BOOT.
Code Cleanup:
The SECURE_BOOT specific defines have been moved from
arch-ls102xa/config.h to
arm/include/asm/fsl_secure_boot.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.
Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There 4 JRs, 4 RTICs and 8 DECOs, and set them the same stream id
for using the same SMMU3 on LS1021A.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins
0x48_00000000. In order to access PCIe device, we must create
TLB to map the 40bit physical address to 32bit virtual address.
This patch will enable MMU after DDR is available and creates MMU
table in DRAM to map all 4G space; then, re-use the reserved space
to map PCIe region. The following the mapping layout.
VA mapping:
------- <---- 0GB
| |
| |
|-------| <---- 0x24000000
|///////| ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000
|-------| <---- 0x300000000
| |
|-------| <---- 0x34000000
|///////| ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000
|-------| <---- 0x40000000
| |
|-------| <---- 0x80000000 DDR0 space start
|\\\\\\\|
|\\\\\\\| ===> 2GB VA map for 2GB DDR0 Memory space
|\\\\\\\|
------- <---- 4GB DDR0 space end
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch is to define default values for some CCSR macros
to make header files cleaner.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they
do not support GPIO.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h>
to support OF_CONTROL for LS102x platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After wakeup from deep sleep, Clear EPU registers as early as possible
to prevent from possible issue. It's also safe to clear at normal boot.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are 8 SCFG_SPARECR registers in SCFG memory block, not one.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
This patch is to add DCU driver support. DCU also named
2D-ACE(Two Dimensional Animation and Compositing Engine)
is a system master that fetches graphics stored in internal
or external memory and displays them on a TFT LCD panel.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Aneesh Bansal
Shengzhou Liu
Yao Yuan
Alison Wang
tang yuantian
Mingkai Hu
horia.geanta@freescale.com
Zhuoyu Zhang
Claudiu Manoil
Aneesh Bansal
Ruchika Gupta
Nikhil Badola
Ramneek Mehresh
York Sun
Zhao Qiang
gaurav rana
Minghuan Lian
Xiubo Li
chenhui zhao
Jason Jin