This contains support for the following components:
- DUART
- MMC
- Both FEC interfaces
- NAND
- I2C (RTC, EEPROM)
- SPI (FLASH)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
add new configuration file da850_am18xxevm.h for AM18xx boards
which are based on da850 SOC. AM18xx has WINBOND spi flash which
is indicated in the config file. And make appropriate changes in
board.cfg for building.
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Alter the board.cfg to pass core module configuration flags
so we can make compile-time switches for different core
modules. These are already in use for some low-level code,
they just got lost in the conversion to the new build
system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add new configuration file for dm6467T and appropraite changes
in boards.cfg. dm6467T is the new varaiant of dm6467 SOC which
supports 33 MHz reference clock where as dm6467 supports 27 MHz
reference clock.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The new MPC8360EMDS board changes the oscillator to 33.33MHz
in order to support QE 500MHz since 2008.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move the coldfire boards to boards.cfg. The config name
for the EB+MCF-EV123 boards are changed to EB-MCF-EV123
as the '+' cannot be recognized.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Add support for the MATRIX VISION mvBlueLYNX-X, an OMAP3-based
intelligent camera.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- DM368 SOC
- booting with spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
the RAM with the post memory test. If error
is found, switch all LEDs on and halt system.
- SPI Flash
Dataflash Typ: M25PE80
- Ethernet DM9161BI
- MMC
- USB
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The Xilinx FPGA must be reconfigured each time the unit
reboots. The FPGA is connected to the GPIO pin 39 from kirkwood.
This patch triggers this pin for km_kirkwood_pci targets.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This adds basic board support for TT-01 based on
the Bluetechnix i.MX31 SOM. Currently only NOR-Flash
boot is implemented.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
The flea3 board is a custom board by CarMediaLab used
in automotive.
Network (FEC), NOR, NAND and SPI are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add basic support for Calxeda Highbank platform. Only minimal support with
serial and SATA are included.
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.
CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h. Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Currently there are two config options for building a U-boot binary for MX31PDK:
make mx31pdk_config
or,
make mx31pdk_nand_config
mx31pdk_config was developed first when no NAND SPL support was available for
MX31 and it requires that the U-boot binary is loaded into RAM via JTAG and it
forces SKIP_LOWLEVEL_INIT.
mx31pdk_nand_config was added later and it allows booting from NAND Flash.
Leave just one config option called mx31pdk so that it produces a binary that can boot from NAND Flash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The board stopped building some time ago, and the board maintainer
agrtees to drop it - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112674
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
This adds basic files for the sandbox board. The lds file is very simple
since we can rely mostly on the linker defaults.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for the qi_lb60 (a.k.a QI Ben NanoNote) clamshell device
from Qi hardware:
http://en.qi-hardware.com/wiki/Ben_NanoNotehttp://en.qi-hardware.com/wiki/Main_Pagehttp://en.wikipedia.org/wiki/Qi_hardware
This Jz4740-based clamshell device does not use NOR flash to boot.
The initial bring-up assumes that U-Boot is directly loaded into SDRAM
using USB boot tool, and starts from 0x80100000.
About USB boot tool
-------------------
Jz4740 is one of the XBurst processors with USB boot functionality
supported. The CPU can boot from a small ROM in the LSI, initialize
CPU and USB module, then wait for USB commands from the USB host.
We can send 8 KB binary data to the CPU cache using USB boot tool.
USB boot tool is available to the public at Ingenic website. Also
there is an alternative Debian package named xburst-tools.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
An entry in the main Makefile for the mx31pdk board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
And various defines to enable NAND support and NAND spl code for the
P1010RDB platform.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Marek Vasut
Nagabhushana Netagunte
Linus Walleij
Macpaul Lin
Manjunath Hadli
Jerry Huang
Jason Jin
Michael Jones
Heiko Schocher
Sanjeev Premi
Holger Brunck
Helmut Raiger
Stefano Babic
Rob Herring
Chandan Nath
Jason Cooper
Fabio Estevam
Wolfgang Denk
stany MARCEL
Simon Glass
chenhui zhao
Kuldip Giroh
Xiangfu Liu
Ruchika Gupta
Kumar Gala
Paul Gortmaker
Dipen Dudhat
Poonam Aggrwal
Li Yang
Albert ARIBAUD
Chander Kashyap