Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on Freescale i.MX53 SoC.
http://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the
commit: 89ebc82137
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Include/fsl_sec.h defines sec_in and sec_out, according to the
platform's endianess. Therefore, CONFIG_SYS_FSL_LE needs to be
declared in the configuration file of the target, in order to use
enable the DEK blob generation command. This requirement is not
explicit in the README.mxc_hab.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Since commit 32df39c741 ("mx5: fix get_reset_cause") we have the following
boot messages on a mx53qsb:
U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: POR
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
CPU: Freescale i.MX53 rev2.1 at 1000 MHz
Reset cause: unknown reset
Net: FEC [PRIME]
The CPU and Reset cause lines appear twice.
Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via
I2C to raise the CPU voltage so that it can run at 1GHz.
To avoid such misleading double printings, disable printing cpu info for now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
with WCR_WDW set, the watchdog won't trigger if we bootet linux and idle
around while the watchdog is not triggered. It seems the timer makes
progress very slowly if at all. I managed to remain 20minutes alive
while the timeout was set to 60secs. It reboots within 60secs if I start
a busyloop in userland (something like "while (1) { }").
While I don't see a reason why the WDT should not be running while the
CPU is in idle, I'm dropping this bit.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Before add CONFIG_SYS_MALLOC_F and CONFIG_SYS_MALLOC_F_LEN,
uboot will complains "CPU: Temperature: Can't find sensor device".
This is because DM and DM_THERMAL are enabled, but SYS_MALLOC_F
is not configured.
After applying this patch, uboot can correctly detect the temperature.
"
U-Boot 2015.04-rc2-00146-g48b6e30-dirty (Mar 09 2015 - 13:04:36)
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
CPU: Temperature 44 C
"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
IMX_CONFIG is currently passed via the SYS_EXTRA_OPTIONS which is marked
as deprecated.
Add a new Kconfig file under arch/arm/imx-common and define the
IMX_CONFIG Kconfig in there.
Each board is supposed to provide a default value pointing to the
appropriate imximage.cfg file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Freescale boards are currently all defined in arch/arm/Kconfig, which
makes them hard to detect.
Moreover the MX6 SoC variant (Q, D, DL, S, SL) selection is currently
done via the SYS_EXTRA_OPTIONS option which marked as deprecated.
Move to a more standard way to select sub-architecture and board by
creating a Kconfig under arch/arm/cpu/armv7/mx6 and a new ARCH_MX6
option.
Existing MX6 board definitions should be moved in this new Kconfig in
choice menu, and new boards should be directly declared in this menu.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If the GBE bit is set, when do next time autonegotiation,
if the result is not 1000Mbps, it will fallback to 100Mbps
checking. So, we need to clear the GBE bit.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
As the u-boot-spl.lds is used only for armv7 SoCs (includes
sama5d3 and sama5d4), so move it to armv7 directory.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
As the u-boot-spl.lds is moved to <arch/arm/mach-at91> directory.
So, correct the path for sama5d4 related boards.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
HUSH parser will handle the variable easier. That will be helpful for
write a complicated U-Boot commands or varaibles.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
This patch enable the MCI support for at91sam9rlek board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase on ToT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Update the nand flash offset mapping, default nand bootcmand and
bootargs to align with linux4sam.org.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
The current implementation for baudrate calculation is incorrect.
This part from the formula:
"2 ^ (n + 1)" is not equivalent to (1 << n) but to (2 << n)!
This patch fixes this and moves this calculation to a function instead of using a macro.
This new function is taken from the Linux kernel.
This was detected and tested on the Marvell Armada A38x DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
SDHCI_HOST_CONTROL is a byte-sized register, so don't write to it
as if it were a long, as that would result in clobbering the three
registers following.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Properly mask SELBASECLK by using an actual mask rather than the
number of bits to shift in order to create the mask.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
- add more targets for building with buildman:
- avr32
- m68k
and while at it, sort the list alphabetical
Reviewed-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Erik Theisen <etheisen@mindspring.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We don't want that CONSOLE is redirected to LCD upon init, we rather prefer
that console is still on the serial line.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The build break was caused by one of my previous commit:
'odroid: defconfig: disable memset at malloc init'
It removes the dts from odroid defconfig - rebase mistake.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Since commit e02ee2548a (kconfig: switch to single .config
configuration), the prefixes in defconfig files such as "+S:",
"+ST:", etc., are meaningless.
This commit was generated by the following command:
find configs -name '*_defconfig' | xargs sed -i 's/^+*S*T*://'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the case of BUILD_NBUILDS > 1, MAKEALL would try to print the size
immediately after the u-boot binary is deleted by the call to:
make -s clean
Move the size print to before the clean
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Driver Model description in README was removed by commit
65eb659e56 (README: remove description about driver model
configuration options), and was revived by mistake by commit
b79dadf846 when resolving the conflict.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Andrej Rosano
Ulises Cardenas
Fabio Estevam
Sebastian Siewior
Peng Fan
Boris BREZILLON
Tom Rini
Bo Shen
Wu, Josh
Stefan Roese
Rob Herring
Matt Reimer
Kim Phillips
Heiko Schocher
Masahiro Yamada
Hannes Petermaier
Przemyslaw Marczak
Joe Hershberger