Another round of sorting Kconfig entries aplhabetically.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Trivial Kconfig cleanup. Use tabs instead of spaces and every Kconfig
entry should be separated by newline.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
When called with ENVOP_SAVE, env_get_location() only returns the
gd->env_load_location variable without actually checking for
the environment location and priority.
This behaviour causes env_save() to fall into an infinite loop when
the low-level drv->save() call fails.
The env_save() function should not loop through the environment
location list but it should save the environment into the location
stored in gd->env_load_location by the last env_load() call.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Remove additional trailing whitespaces in prompt reported by kconfiglib:
warning: DM_PMIC_SANDBOX (defined at drivers/power/pmic/Kconfig:133) has
leading or trailing whitespace in its prompt
warning: <choice> (defined at dts/Kconfig:204) has leading or trailing
whitespace in its prompt
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
This reverts commit 5e5745465c.
The reverted commit didn't support the scenario where there are less
DRAM banks in U-Boot than in Linux.
Also, it didn't introduce any new functionality, only limitaion.
User could just increase MEMORY_BANKS_MAX if it's too small.
Reviewed-by: Simon Glass <sjg@chromium.org>
With the pending requirement for CONFIG_BLK, this patch removes
the USB_STORAGE option which assumes that DM_USB is enabled, but isn't
yet available for the omap2340 musb glue among other issues. Once
the USB issues are resolved, a future patch can enable them again.
Signed-off-by: Adam Ford <aford173@gmail.com>
The driver sets the weekday incorrectly when called by the
'date set' command.
Sunday is 1, Saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf, table 3).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Now that TPMv1 and TPMv2 can be compiled at the same time, let's compile
them both with Sandbox as well as both drivers (and, it is already
implied in Kconfig: both commands).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TPM_V1 was already compiled by default. Now that both can be compiled
at the same time, compiled them both by default.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While using the 'tpm' command should work on most cases, this test suite
only works with TPMv2 and since the work to make both versions build at
the same time, we might end up having both 'tpm' (TPMv1) and 'tpm2'
(TPMv2) commands available at the same time. Ensure this test suite
always use the right one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While there is probably no reason to do so in a real life situation, it
will allow to compile test both stacks with the same sandbox defconfig.
As we cannot define two 'tpm' commands at the same time, the command for
TPM v1 is still called 'tpm' and the one for TPM v2 'tpm2'. While this
is the exact command name that must be written into eg. test files, any
user already using the TPM v2 stack can continue to do so by just writing
'tpm' because as long as TPM v1 support is not compiled, U-Boot prompt
will search for the closest command named after 'tpm'.
The command set can also be changed at runtime (not supported yet, but
ready to be), but as one can compile only either one stack or the other,
there is still one spot in the code where conditionals are used: to
retrieve the v1 or v2 command set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: In sandbox_tpm2_fill_buf() use NULL not \0 to ensure NULL
terminated string due to LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
The TPM_DRIVER_SELECTED symbol was used in one of the initial series
about TPMv2 but its use has been dropped, making these selects
useless, remove them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Sandbox and the TPM stack are both selected, compile Sandbox TPM
driver by default.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The udevice given to the open() function of course must be opened,
not closed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With some recent changes to relevant drivers here the openrd board
(openrd_client in this case) does not fit within its size constraint.
We can however drop the slightly extended baudrate table and then the
duplication of mtdparts/mtdids in the default environment. These
defaults are set in the environment by the 'mtdparts' command and
otherwise referenced throughout the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
fdt_fixup_mtdparts() calls mtdparts_init() and device_find(),
which are defined in cmd/mtdparts.c
The combination of FDT_FIXUP_PARTITIONS=y and CMD_MTDPARTS=n
emits the following link error:
common/fdt_support.c:903: undefined reference to `mtdparts_init'
common/fdt_support.c:914: undefined reference to `device_find'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prior to this patch is fdtdec_setup_memory_banksize() incorrectly
ignoring the "status" field. This patch fixes that by testing the status
with fdtdec_get_is_enabled() before using a memory node.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previously the first three words in a git-mailrc alias entry could only
be separated by spaces. git-send-email and Mutt both allow arbitrary
whitespace here.
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
patman's _ReadAliasFile only splits on spaces, not tabs, so the entries
for dinh and maxime weren't being recognised as valid. I'll fix patman
in a separate patch, but this makes all the entries consistent.
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix warning when compiling tegra30-beaver/-apalis.dts with latest DTC:
"Warning (avoid_unnecessary_addr_size): /pci/pch@1f,0: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property"
Signed-off-by: Tom Warren <twarren@nvidia.com>
If a secure carveout exists, U-Boot cannot use that memory. Fix
carveout_size() to reflect this, and hence transitively fix
usable_ram_size_below_4g() and board_get_usable_ram_top(). This change
ensures that when U-Boot copies the secure monitor code to install it, the
copy target is not in-use for U-Boot code/data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When fixing up the DT to report PSCI support, explicitly enable the node.
DTs may ship with the node disabled in case a PSCI implementation is not
present, and expect any PSCI implementation to enable the node if they are
actually present.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enhance the PSCI DT editing code to allow setting a PSCI v0.2 compatible
value in the DT. The CONFIG_ option is added to the whitelist to match the
existing PSCI_1_0 option. While not adding new options to Kconfig isn't
ideal, I figure it's better to keep related options together.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a MON_MODE define for ARM's monitor mode. This can be used later by
a secure monitor to avoid hard-coding mode IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RAM repair has a few pre-requisites:
1) PMIC power supply (rail) enabled.
2) PMC CRAIL power partition powered.
3) Fuse clock active (it's the default).
4) PLLP reshift branch enabled (it's the default, when PLLP is active).
RAM repair also only need run whenever specific partitions are powered
(main SoC and CCPLEX respectively); RAM repair does not need to be
triggered when any other partition changes state.
start_cpu() needs to be re-ordered slightly to match these requirements.
Note that C0NC and CE0 aren't required for RAM repair to
operate, but they also do no harm, so the entire of powerup_cpus() is
moved rather than splitting it up. The call to remove_cpu_resets() is
moved last to ensure that all other actions complete before releasing
reset; since the PMC power partitions are now enabled early, releasing
reset is what causes the CPUs to start executing code, and RAM repair must
complete before the CPU boots.
Note that this commit is the result of squashing a numbmer of commits
in NVIDIA's downstream L4T branch, hence the multiple signoffs below.
Signed-off-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reverts commit 701b7b1d2c. It will
be immediately replaced by a different implementation that is more
complete and runs are more targetted times.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use GNU make pattern rules to indicate that a single run of binman
produces all three Tegra output files. The avoids make running binman
three times (perhaps in parallel) and those instances inteferring with
each other.
See http://patchwork.ozlabs.org/patch/944611/ for the bug report.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Scott is no longer maintaining the NAND subsystem, mark as orphaned for
now.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch updates the zynq gem driver to support livetree.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now zynq_gem driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Now CPSW driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use PHY API phy_get_ofnode() helper to get PHY DT node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use PHY API phy_get_ofnode() helper to get PHY DT node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):
- network drivers
priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
<-- phydev is connected to dev which is UCLASS_ETH device
if (priv->phy_of_handle > 0)
dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
<-- phydev->dev->node is overwritten by phy-handle DT node
- PHY driver in .config() callback
int node = dev_of_offset(dev);
<-- PHY driver uses overwritten dev->node
const void *fdt = gd->fdt_blob;
if (fdtdec_get_bool(fdt, node, "property"))
...
As result, UCLASS_ETH device can't be used any more for DT accessing.
This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.
Also, common.h includes config.h as the first thing it does, so don't
include it directly.
Series-to: u-boot
Series-cc: Grygorii Strashko <grygorii.strashko@ti.com>
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.
[1] https://patchwork.ozlabs.org/cover/940104/
END
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Because some phy wants to export some functions [1], export.h was
including the whole phy subsystem which pulls in lots of stuff that
causes some ordering and redefinition issues. Split out the only part
that is actually needed in export.h and include it there and in phy.h.
[1] commit 9527931507 ("board/ls2085rdb: Export functions for
standalone AQ FW load apps")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The include/phy.h will start including dm.h, which pulls in
linux/compat.h after the attempted redefinition in
arch/arm/include/asm/armv8/mmu.h, so move this include to allow
redefinition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Switch to use more generic ofnode API instead of FDT API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).
It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.
Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Add driver model support to the mvgbe driver. As a temporary measure
both DM and non-DM uses are supported. Once all the users have been
converted the non-DM support can be dropped.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extract some function bodies to helper functions that can be reused in
the DM/non-DM implementations.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if_type is not correctly initialized
Failure to initialize if_type means that grub2/efinet sends
a bogus arp request. It therefore gets no response. On Raspberry Pi 3B+
this leads to a pause at:
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek
Nicholas Faustini
Ramon Fried
Adam Ford
Heinrich Schuchardt
Miquel Raynal
Tom Rini
Masahiro Yamada
Jens Wiklander
Chris Packham
Adam Sampson
Tom Warren
Stephen Warren
Bibek Basu
Simon Glass
Siva Durga Prasad Paladugu
Grygorii Strashko
Joe Hershberger
Murali Karicheri
Andrew Thomas