The real reason for memory instability was the fact that the EMI block
was gated and not reset throughout the boards' operation. This patch
resets the EMI block properly while also reverts the memory voltage bump.
The memory stability issues were caused by the EMI not being reset properly
and thus there is no longer need to run the memory at higher voltage than
it ought to run at.
This partly reverts 8303ed128a .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Including header for pads is not needed and breaks board
after renaming pin definitions.
Series-to: u-boot
Series-cc: marex@denx.de,fabio.estevam@freescale.com,eric.nelson@boundarydevices.com
Signed-off-by: Stefano Babic <sbabic@denx.de>
Rename all i.MX6 pad declarations to MX6_PAD_x, so a board
may support either i.MX6Quad/Dual (MX6Q) or i.MX6Dual-Lite/Solo
(MX6DL) by including the proper header.
Boards mx6qarm2, mx6qsabreauto, mx6qsabrelite, and mx6qsabresd
only support MX6Q, so they include mx6q_pins.h.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Commit 8b710b1 started removing code for the unmaintained "ns9750dev"
board; the board support is still broken, and not included anywhere in
the Makefile or boards.cfg. Remove the remaining dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Currently sata usage text prints a double 'sata' for the init command.
MX53LOCO U-Boot > sata
sata - SATA sub system
Usage:
sata sata init - init SATA sub system
sata info - show available SATA devices
sata device [dev] - show or set current device
sata part [dev] - print partition table
sata read addr blk# cnt
sata write addr blk# cnt
Remove the extra 'sata' from the 'sata init' line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This pulls the three following ZYNQ commits into ARM master:
7dca54f8: xilinx: zynq: Enable DCC and create new zynq_dcc board
59c651f4: arm: zynq: Add SLCR support with system reset
00ed3458: arm: zynq: Add lowlevel initialization to C
This target will move the environment into SPI flash and documents
the expected layout. We correct the SPL define for where U-Boot is
and remove an unused define.
Signed-off-by: Tom Rini <trini@ti.com>
Added README file with the description of required options and host
configuration to use network SPL with am335x targets. Briefly discuss
how to use this configuration to program empty boards.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added variables to support SPI booting
* Note that the first 512KiB are reserved for 4 copies of SPL.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added support to the default environment variables for NAND
boot.
* Add nandboot to the default bootcmd.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Rather than load the FPGA file from the FAT partition, look
at entry in system EEPROM to decide which file to retrieve directly
from the EXT3 partition.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Also, change bootdelay to 0 but allow pressing 'S' to stop at U-Boot prompt.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard Gray <howard.gray@matrix-vision.de>
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Current '#if' directives (used in igep00x0.h config file) comparing MACH_TYPE
values in igep00x0.h doesn't work as expected. The comparision between
CONFIG_MACH_TYPE and MACH_TYPE_IGEP0020 is always true independent of the IGEP
machine configured.
For example, following directive
if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020)
define something
endif
Is always evaluated true although we configure u-boot for MACH_TYPE_IGEP0030.
The build doesn't shows any error so looks that both defines had always the same
value. Including the mach-types.h file sets properly the value of
MACH_TYPE_IGEPxxxx.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds BOOT_DEVICE define for USB booting and fixes
spl_board_init function to call arch_misc_init (this is the place there
musb is initialized).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
In case of usbeth booting just call net_load_image("usb_ether").
This patch also adds CONFIG_SPL_USBETH_SUPPORT and
CONFIG_SPL_MUSB_NEW_SUPPORT config options to enable linking of SPL
against USB gagdet support and new MUSB driver resp.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The pcm051 does not have the wp pin connected to the sd-card socket.
Therefore remove the pinmux for the pin. The was a carry-over from
the am335x evm code.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
The pinmux was generated from linux/arch/arm/mach-davinci/da830.c as of
kernel version 3.7.5. If the driver is used for the da850, then SoC
variant must be specified by CONFIG_SOC_DA850.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Tom Rini <trini@ti.com>
Remove the manual relocation of env_name_spec. This has been missed
in the previous patch series for introducing dynamic relocation
on MIPS.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This code is pretty old and we want to support only 32-bit systems now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Invert the polarity of this option to simplify the Makefile logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gabe Black <gabeblack@chromium.org>
These lines are dealt with in the x86 Makefile and link script, so punt
them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gabe Black <gabeblack@chromium.org>
This x86 CPU variant is no longer required as the boards that use it have
been removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
The code handles relocation entries with the
following relocation types only:
mips32: R_MIPS_REL32
mips64: R_MIPS_REL+R_MIPS_64
xburst: R_MIPS_REL32
Other relocation entries are skipped without
processing. The code must be extended if other
relocation types must be supported.
Add -pie to LDFLAGS_FINAL to generate the .rel.dyn
fixup table, which will be applied to the relocated
image before transferring control to it.
The CONFIG_NEEDS_MANUAL_RELOC is not needed
after the patch, so remove that as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This section contain the table needed for dynamic
relocation. Also provide symbols for the relocation
code to access the table.
Discard all sections which are not needed in the final
ELF binary and U-Boot image. Section .dynsym cannot be
discarded or GNU ld crashes otherwise. This section
will be stripped by GNU objcpy in a later patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use the newly introduced symbol __image_copy_end as end address for
relocation of U-Boot image. This is needed for dynamic relocation added
in later patches. This patch obsoletes the symbols uboot_end and
uboot_end_data which are removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Get the start and end address for clearing BSS from the newly
introduced symbols __bss_start and __bss_end. After GOT is
relocated, those symbols are already pointing to the correct
addresses.
Also optimize the loop by moving the address incrementation
to the delay slot to avoid the initial sub instruction.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use the newly introduced symbols __image_copy_end and __bss_end
for setting up the memory area for the relocated U-Boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This symbol is used in later patches as end address
for relocation of the U-Boot image into RAM.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
These symbols are used in later patches for as addresses for
clearing the BSS area in the relocated U-Boot image.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The '__got_start' and '__got_end' symbols are used
only in the linker script to compute the value of
the 'num_got_entries' symbol.
Remove the symbols and use the SIZEOF(.got) command
to get the size of the .got section.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Marek Vasut
Stefano Babic
Eric Nelson
Wolfgang Denk
Fabio Estevam
Albert ARIBAUD
Tom Rini
Ilya Yanok
Chase Maupin
Michael Jones
Howard Gray
Enric Balletbo i Serra
Lars Poeschel
robertcnelson@gmail.com
Tomas Novotny
Daniel Schwierzeck
Simon Glass
Gabor Juhos