This should make it clear that this symbol is meant to be defined by
board headers.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
This is tested on the DB-MV784MP-GP eval board. To really enable ECC
support on this board the I2C EEPROM needs to get changed. As it
saves the enabling of ECC support internally. For this the following
commands can be used to enable ECC support on this board:
Its recommended for first save (print) the value(s) in this EEPROM
address:
=> i2c md 4e 0.1 2
0000: 05 00 ..
To enable ECC support you need to set bit 1 in the 2nd byte:
Marvell>> i2c mw 4e 1.1 02
Marvell>> i2c md 4e 0.1 2
0000: 05 02 ..
To disable ECC support again, please use this command:
Marvell>> i2c mw 4e 1.1 00
Marvell>> i2c md 4e 0.1 2
0000: 05 00 ..
On other AXP boards, simply plugging an ECC DIMM should be enough to
enable ECC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the AXP boot image. Not linked with the main U-Boot. With this code
addition and the following serdes/PHY setup code, the Armada-XP support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion. Hopefully other MVEBU SoC's will follow here.
Support for some SoC's has been removed in this version. This is:
MV_MSYS:
The code referred to by the MV_MSYS define is currently unused. And its
not really planned to support this in mainline. So lets remove it to
make the code clearer and increase the readability.
MV88F68XX (A38x):
The code referred to by the MV88F68XX define (A38x) is currently unused.
And its partial and not sufficient for this device in this stage.
So lets remove it to make the code clearer and increase the readability.
MV88F66XX (ALP):
The code referred to by the MV88F66XX define is currently unused. And its
not really planned to support this in mainline. So lets remove it to
make the code clearer and increase the readability.
MV88F78X60_Z1:
The code referred to by the MV88F78X60_Z1 define is currently unused. As the
Z1 revision of the AXP is not supported in mainline anymore.
So lets remove it to make the code clearer and increase the readability.
Remove support for Z1 & A0 AXP revisions (steppings). The current stepping
is B0 and this is the only one that is actively supported in this code
version.
Tested on AXP using a SPD DIMM setup on the Marvell DB-MV784MP-GP board and
on a custom fixed DDR configuration board (maxbcm).
Note:
This code has undergone many hours of coding-style cleanup and refactoring.
It still is not checkpatch clean though, I'm afraid. As the factoring of the
code has so many levels of indentation that many lines are longer than 80
chars. This might be some task to tackly later on.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Phil Sutter
Stefan Roese