The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
Armada 375 still has some problems with d-cache enabled in the ethernet
driver (mvpp2). So lets keep the d-cache disabled until this is solved.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the Armada 375. Please note that
currently the SerDes and DDR3 init code for the A375 is not
included / enabled. This will be done in a later, follow-up patch.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
These attribute defines may be used to map an area of memory for direct
access to the specific SPI devices. See SPI Direct Access Mode for
further information.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the LCD controller of the Marvell
Armada XP SoC.
An AXP based custom board port will be added later, to use this
driver to display a splash screen via the bmp command later.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds basic support for Marvell's MV78230 SoC which belongs to the
Armada XP series.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds intermediate kconfig symbols which select their SoC
family. Boards then select them instead of the family symbol directly.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of calling board_sat_r_get() only for those boards providing the
satr11 value via I2C, call it for all boards and return static values
for those not using I2C.
In addition to that, make this a weak function to allow for board code
to override it.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Armada XP has support for X4 lanes, boards specify this in their
serdes_cfg. During PEX init in high_speed_env_lib.c, the configuration
is stored in GEN_PURP_RES_2_REG.
When enumerating PEX, subsequent interfaces of an X4 lane must be
skipped. Otherwise the enumeration hangs up the board.
The way this is implemented here is not exactly beautiful, but it mimics
how Marvell's BSP does it. Alternatively we could get the information
using board_serdes_cfg_get(), but that won't lead to clean code, either.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds runtime detection of the Marvell UART boot-mode (xmodem
protocol). If this boot-mode is detected, SPL will return to the
BootROM to continue the UART booting.
With this patch its now possible, to generate a U-Boot image that
can be booted either from the strapped boot-device (e.g. SPI NOR, MMC,
etc) or via the xmodem protocol from the UART. In the UART case,
the kwboot tool will dynamically insert the UART boot-device type
into the image. And also patch the load address in the header, so
that the mkimage header will be skipped (as its not expected by the
Marvell BootROM).
This simplifies the development for Armada XP / 38x based boards.
As no special images need to be generated by selecting the
MVEBU_BOOTROM_UARTBOOT Kconfig option.
Since the Kconfig option MVEBU_BOOTROM_UARTBOOT is not needed any
more, its now completely removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
This patch adds runtime boot-device detection to SPL U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
As these structs are local only and const, declare them accordingly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
This is preparation for the runtime bootmode detection in spl.c.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Merging all the board specific Kconfig options into the main Kconfig file
for mach-mvebu makes things easier to maintain.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
With this patch, the CPU and the DDR frequencies will get printed in the
U-Boot startup messages. Resulting in such a log:
U-Boot 2016.01-rc2-00188-gb8eeaec-dirty (Dec 21 2015 - 12:32:35 +0100)
SoC: MV78460-B0 at 1600 MHz
I2C: ready
DRAM: 4 GiB (800 MHz, ECC not enabled)
...
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Change some of the PEX configuration output lines from always output to
only ouput upon specific debug enabling.
This changes the SPL output from:
U-Boot SPL 2016.01-rc2-00037-g9353a7f (Dec 10 2015 - 10:27:42)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
Update Device ID PEX0782611ab
Update Device ID PEX1782611ab
Update Device ID PEX2782611ab
Update Device ID PEX3782611ab
Update Device ID PEX8782611ab
Update PEX Device ID 0x78260
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
to:
U-Boot SPL 2016.01-rc2-00037-g9353a7f-dirty (Dec 10 2015 - 10:32:04)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
Resulting in a little faster bootup time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is not needed any more since the switch to DM / DTS network
initialization on MVEBU. Lets remove it, as it otherwise leads
to compilation warning when CONFIG_NET is not enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the dual core Armada XP variant, the
MV78260. It has some minor differences to the 4-core MV78460,
e.g. only 12 serdes lanes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
Using board ID 0 is reserved for the non-Marvell "custom" boards. So
move the board ID's to reflect this.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
Use the clrbits() / setbits() functions instead of clrsetbits() when
bit are only cleared or set.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch leaces the cache configuration untouched for the AXP in the
setup done by the BootROM. Resulting in the cache still being enabled
at the startup of U-Boot. This leads to a slightly faster boot to the
U-Boot prompt (or Linux of course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch removes the call to arch_cpu_init() in the SPL U-Boot version.
As SPL does not need all the configuration done in this function. And
also does not need the reconfiguration of the internal register
address to 0xf1000000. This will be done by the main U-Boot later on.
This also fixes a problem with the timer not beeing initialized on AXP,
as needed for the mdelay in the setup_usb_phys(). This will now only
be called once in main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add functionality to correctly disable the L2 cache on the Armada XP
and 38x platforms.
Without this, booting into Linux on ClearFog (A38x) results in a hangup
without any output on the serial console at all. Even with earlyprintk
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Until now, the L2 cache was never enabled again in U-Boot. To get
even better performance (bootup time), lets enable the L2 cache
in U-Boot. This code was taken from the Linux kernel.
A performance gain was measured on the DB-MV784MP-GP board by testing
with tftpboot and sata commands.
This patch also cleans up the L2 cache related code. And makes sure that
the L2 cache is only disabled once.
Please note that A38x still runs with L2 cache disabled. And needs
to be enabled for this SoC in a separate patch if needed or desired.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
By using the common timer functions for mvebu/kirkwood we can get rid of quite
a lot of code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
As some MVEBU platforms using the MVNETA driver seem to miss the
first ARP packet, lets reduce the timeout and increase the retry
count. This increases the speed for communication establishment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it. Also, allow the board to only specify the lanes that are
used instead of including unused lanes.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Functions that do not modify the pointer passed should declare it
as const.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch adds driver model support for some Marvell MVEBU SoC's. Including
Armada XP and 38x. All 3 currently mainlined boards are converted. DM is now
selected automatically for MVEBU platforms.
With this DM support now available for MVEBU, hardcoding the base addresses
and other information is not necessary any more. Probing should be done
by using the values provided via the device tree now instead. For this
the driver also need to be converted to DM. Patches for some of the drivers
will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the MVEBU SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the use of the kwboot tool, to boot mainline U-Boot
on the Marvell Armada XP/38x SoC's. This is done by returning to the
SoC's BootROM after SPL has initialized the SDRAM. We need to make sure
to not reconfigure the internal register space and MBARs. Otherwise
the BootROM will not be able to continue after SPL jumps back to it.
To use this feature, please don't forget to change the BOOT_FROM line
in your board specfic kwbimage.cfg file this way:
BOOT_FROM uart
Tested on these Marvell eval boards:
DB-MV784MP-GP - Armada XP
DB-88F6820-GP - Armada 38x
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As reported by Simon Guinot, commit ade741b3
"arm: mvebu: Call timer_init early before PHY and DDR init" breaks
Kirkwood platforms. As the static variable "init_done" is not
available at that early boot time. This patch moves it to explicitly
to the data section, making it available at that time.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Currently booting on A38x is broken. As the current code tries to detect
the SoC family to disable the MMU for the A38x at runtime. But before the
internal registers are switched to the new location (0xf100.0000), this
runtime detection does not work. As all macros / defines are already
assigned to the new location at 0xf100.0000. But the registers are sill
mapped to the default location at 0xd000.0000.
This patch now makes sure, no such runtime detection is used before
the internal registers are configured to the new location. After this,
the remaining cache cleanup is executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds a PCI driver for the controllers found on Marvell MVEBU SoCs.
Besides the driver, this patch also removes the statically defined
PCI MBUS windows. As they are not needed anymore, since this PCIe
driver now creates the windows dynamically.
Tested on Armada XP db-mv784mp-gp eval board using an Intel E1000
PCIe card in all 3 PCIe slots. And on the Armada 38x db-88f6820-gp
eval board using this Intel E1000 PCIe card in the PCIe 0 slot.
This port was done in cooperation with Anton Schubert.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Marek Vasut
Tom Rini
Stefan Roese
Phil Sutter
Kevin Smith
Fabio Estevam
Heiko Schocher
Anton Schubert