There is the requirement on the chassis's backplane that when the clocks
have been enabled, they then should not disappear.
Resetting the Zarlink clocking chips at unit reset violates this
requirement because the backplane clocks are not supplied during the
reset time.
To avoid this side effect, both the Zarlink clocking chips are reset
only at power up.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2
For fiber cable:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When u-boot initializes the RAM (early in boot) it looks for the "pram"
env variable to know which is area it cannot use. If the "pram" env variable
is not found, the default CONFIG_PRAM value is used.
This value used to be 0 (no protection at all). This patch sets it to a
value that covers PHRAM and PNVRAM that must be protected in our case.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This Patch updates error print for QE which should be easily understood
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If hwconfig does not contains "en_cpc" then by default all cpcs are enabled
If this config is defined then only those individual cpcs which are defined
in the subargument of "en_cpc" will be enabled e.g en_cpc:cpc1,cpc2; (this
will enable cpc1 and cpc2) or en_cpc:cpc2; (this enables just cpc2)
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This commit adds new test for UMS USB gadget to u-boot mainline tree.
It is similar in operation to the one already available in test/dfu
directory.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
By mistake I've forgotten to add the SPDX license tags for the DFU testing
scripts.
This commit fixes that and also provides some other relevant information.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
It is now possible to pass to the dfu_gadget_test_init.sh script the sizes
of files to be generated.
This feature is required by UMS tests which reuse this code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
It is necessary to provide the same Vendor and Product IDs as the one in
the original Linux kernel code.
Without this change the USB mass storage gadget is not working with Windows7.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Older versions of git (e.g. Ubuntu 10.04) do not support this flag. By
default they do not decorate. So only enable this flag when supported.
Suggested-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to build only some of the commits in a branch. Add
support for the -c option to allow this. It was previously parsed by
buildman but not implemented.
Suggested-by: York Sun <yorksun@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Currently buildman allows a list of boards to build to be specified on the
command line. The list can include specific board names, architecture, SOC
and so on.
At present the list of boards is dealt with in an 'OR' fashion, and there
is no way to specify something like 'arm & freescale', meaning boards with
ARM architecture but only those made by Freescale. This would exclude the
PowerPC boards made by Freescale.
Support an '&' operator on the command line to permit this. Ensure that
arguments can be specified in a single string to permit easy shell quoting.
Suggested-by: York Sun <yorksun@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
The current README is a bit sparse in this area, so add a few more
examples.
Suggested-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
If buildman finds no problems it prints nothing. This can be a bit confusing,
so add a message that all is well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new --config-file option (-G) to specify a different configuration
file from the default ~/.buildman.
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Normally buildman operates in two passes - one to do the build and another
to summarise the errors. Add a verbose option (-v) to display build problems
as they happen. With -e also given, this will display errors too.
When building the current source tree (rather than a list of commits in a
branch), both -v and -e are enabled automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need the output options to be available in several places. It's a pain
to pass them into each function. Make them properties of the builder and
add a single function to set them up. At the same time, add a function which
produces summary output using these options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Originally buildman had some support for building the current source tree.
However this was dropped before it was submitted, as part of the effort to
make it faster when building entire branches.
Reinstate this support. If no -b option is given, buildman will build the
current source tree.
Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
bootflag as a parameter is passed to board_init_f().
But it is not actually used in this function.
Make it effective by assigned it to gd->flags.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042 has internal display interface unit (DIU) for driving video.
T1042RDB supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used
as HDMI connector on T1042RDB.
This patch add support to
-enable Video interface for T1042RDB
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1042
-program HDMI encoder via I2C on board
This patch refer to the upstream diu patch
(337b0c52b3) for T1040qds.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[York Sun: resolve conflict and move changes to T104xRDB.h]
Reviewed-by: York Sun <yorksun@freescale.com>
The ch7301 encoder not only used in t1040qds platform, so we split
it for t1042rdb and LSx platform.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
most todays LCDs support 32bpp e.g. the framebuffer memory is 32bpp
organized.
To support 24bpp BMPs we need to take only 3 byte from the bpp and set
one byte from the FB to 0.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Since rgb2ycbcr_coeff and friends are declared const, but assigned
to a void pointer, clang will warn that the const is implicity casted
away. If the pointer is changed to void const * gcc will warn when it
is implicitly casted to a const int array. Just add a correctly
typed pointer instead to prevent these casts and hence the warnings.
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Instead of waiting for DC triple buffer to be cleared, this patch
changes to wait for a relevant DP sync flow end interrupt to come
when disabling sync BG flows. In this way, we align the implement
to the freescale internal IPUv3 driver. After applying this patch,
an uboot hang up issue at the arch_preboot_os() stage, where we
disable a relevant ipu display channel, is not observed any more on
some MX6DL platforms.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
- Adds support for a minimal framebuffer driver of TI's AM335x SoC
to be compatible with Wolfgang Denk's LCD-Framework (CONFIG_LCD,
common/lcd.c)
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
This patch removes following two functions:
- lcd_getbgcolor(...)
not used somewhere outside lcd.c, internally we use now the global
variable lcd_color_bg (was return value of function before)
- lcd_getfgcolor(...)
not used in any place of u-boot
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Use the new API which is originally taken out from boot_get_kernel
of bootm.c
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[trini: Fix warnings with CONFIG_FIT]
Signed-off-by: Tom Rini <trini@ti.com>
Trying bootm for zImage will print out several error message which
is not necessary for this case. So detect image format firstly, only
try bootm for legacy and FIT format image then try bootz for others.
This patch needs new function genimg_get_kernel_addr().
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Kernel address is normally stored as a string argument of bootm or bootz.
This function is taken out from boot_get_kernel() of bootm.c, which can be
reused by others.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
[trini: Fix warnings with CONFIG_FIT]
Signed-off-by: Tom Rini <trini@ti.com>
Switch core maintainer to Tom Rini. Adapt directory layout for
git tree detection.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
If a 32-bit system has 2GB of RAM, and the base address of that RAM is
2GB, then start+size will overflow a 32-bit value (to a value of 0).
__lmb_alloc_base is affected by this; it calculates the minimum of
(start+size of RAM) and max_addr. However, when start+size is 0, it
is always less than max_addr, which causes the value of max_addr not
to be taken into account when restricting the allocation's location.
Fix this by calculating start+size separately, and if that calculation
underflows, using -1 (interpreted as the max unsigned value) as the
value instead, and then taking the min of that and max_addr. Now that
start+size doesn't overflow, it's typically large, and max_addr
dominates the min() call, and is taken into account.
The user-visible symptom of this bug is that CONFIG_BOOTMAP_SZ is ignored
on Tegra124 systems with 2GB of RAM, which in turn causes the DT to be
relocated at the very end of RAM, which the ARM Linux kernel doesn't map
during early boot, and which causes boot failures. With this fix,
CONFIG_BOOTMAP_SZ correctly restricts the relocated DT to a much lower
address, and everything works.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h, after which this part of
rpi_b.h was modelled.
The #defines to enable/disable U-Boot commands/features were moved
earlier in rpi_b.h, so they are set up before config_distro_bootcmd.h
is included, since it tests whether certain features should be included
based on those defines.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada
Tom Rini
Valentin Longchamp
York Sun
Shaohui Xie
Vijay Rai
Shaveta Leekha
Lukasz Majewski
Simon Glass
Tang Yuantian
Jason Jin
Wang Dongsheng
Hannes Petermaier
Jeroen Hofstee
Liu Ying
Bryan Wu
Daniel Schwierzeck
Stephen Warren