This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This patch allows to configure all the important DRAM parameters in Kconfig.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In addition to the current Android magic settings, allow to optionally use
DDR3 timing parameters, which are tailored for different clock frequencies
and JEDEC speed bins. This should improve reliability and performance.
Adding '+S:CONFIG_DRAM_TIMINGS_DDR3_1066F_1333H=y' to the board defconfig
allows to use timings, which are calculated for the DDR3-1066F speed bin.
A lot of DDR3 chips, which are used in real Allwinner based devices,
support DDR3-1066F speed bin timings.
And adding '+S:CONFIG_DRAM_TIMINGS_DDR3_800E_1066G_1333J=y' should work
with any DDR3 chips, because this targets the slowest JEDEC speed bins.
The vendor magic values are still used by default for DRAM, but board
maintainers now have more flexibility in DRAM timings selection.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On both my A13-OLinuxIno and my A13-OLinuxIno-Micro, the vga output gives an
unstable image when active low v or hsync is used.
The problem seems to be specific to the OLinuxIno A13 (normal & micro)
boards. I've just looked up the schematics and they use an opendrain driver
for the vga sync lines, and with sync pulses it is the logical high->low
edge of the pulse which counts for the timing, which with an active low
sync is being driven by the pull-up, and that simply seems to not drive
it hard enough to get a stable image.
So force v and hsync active high on these boards. independent of what the
modeline says. This fixes the unstable image.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a low-cost Allwinner A20 board with Arduino-style GPIO headers;
it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro
USB socket for OTG and another for power in, HDMI, SATA, 5V power for
SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a
MIPI camera connector.
Like the BananaPi, this board needs GMAC_TX_DELAY set to 3 in order for
GMAC to work reliably at gigabit speeds.
For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CONFIG_TARGET_FOO was only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), all sun5i and sun7i
boards have been moved over to using a single dram_sun5i_autoconfig file,
and the tx clk delay handling for the Banana boards now has its own Kconfig.
IOW nothing is using CONFIG_TARGET_FOO anymore, so remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Currently we've separate detailed dram settings for all sun5i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
This has been tested on a A10s-Olinuxino, A13-Olinuxino, A13-OlinuxinoM,
mk802-a10s and r7-tv-dongle board.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This brings in a additional small fix which was missed in a recent update
to the README.
Suggested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The Juno Development Platform is a physical Versatile Express
device with some differences from the emulated semihosting
models. The main difference is that the system is split in
a SoC and an FPGA where the SoC hosts the serial ports at
totally different adresses.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Versatile Express ARMv8 semihosted FVP platform is still
using the legacy CONFIG_SYS_EXTRA_OPTIONS method to configure
some compile-time flags. Get rid of this and create a Kconfig
entry for the FVP model, and a selectable bool for the
semihosting library.
The FVP subboard is now modeled as a target choice so we can
eventually choose between different ARMv8 versatile express
boards (FVP, base model, Juno...) this way. All dependent
symbols are updated to reflect this.
The 64bit Versatile Express board symbols are renamed
VEXPRESS64 so we have some chance to see what is actually
going on. Tested on the FVP fast model.
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables CONFIG_DM_I2C and also CONFIG_DM_I2C_COMPAT.
The last one should be removed when the dm pmic framework will
be finished.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
this is an atempt to make the export of functions typesafe.
I replaced the jumptable void ** by a struct (jt_funcs) with function pointers.
The EXPORT_FUNC macro now has 3 fixed parameters and one
variadic parameter
The first is the name of the exported function,
the rest of the parameters are used to format a functionpointer
in the jumptable,
the EXPORT_FUNC macros are expanded three times,
1. to declare the members of the struct
2. to initialize the structmember pointers
3. to call the functions in stubs.c
Signed-off-by: Martin Dorwig <dorwig@tetronik.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(resending to the list since my tweaks are not quite trivial)
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.
This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the STATUS_LED APIs for indicating a boot progress instead of
show_boot_progress.
This patch also fixes a problem introduced with commit b3f4ca1135 (dm: omap3:
Move to driver model for GPIO and serial). After that commit the board doesn't
boot. Looks like the problem is the gpio_request call inside the function
show_boot_progress.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reset isn't instant, so delay to give it a chance. Otherwise we go on
to print a failure message before resetting anyway.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds IDE support to the MIPS Malta board. The IDE controller
is enabled after probing the PCI bus and otherwise just makes use of
U-boot generic IDE support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Dont send always emio value as zero for zynq_gem_initialize
send it based on config.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When diffing through the changes only the relevant changes
should be displayed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Add deep sleep support on Freescale LS1021QDS platform.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021AQDS board.
For ls1021aqds_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the CH7301 HDMI options and the common configuration
for DCU on LS1021AQDS board.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Cc: Jason Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that there are some panels where the pwm input is not active low,
so make it configurable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
HDMI, SATA, USB and Ethernet appear functional, I've not done extensive tests
of all peripherals though.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently we've separate detailed dram settings for all sun7i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
This has been tested on a A20-Olinuxino-Lime, A20-Olinuxino_MICRO, Bananapi,
Bananapro, Cubieboard2, Cubietruck, Mele_M3 and a Linksprite_pcDuino3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The qt840a is one of the many tv-boxes using the "i12" A20 pcb, but it
populates only one of the 2 places for a 16 bit dram ic, thus reducing
the buswidth to 16 bits, and the amount of ram to 512M, which is why we
had a separate config for it.
This commit switches the generic i12-tvbox_defconfig over to DRAM
autoconfiguration, so that it will work with the qt840a too, and drops the
qt840a specific config, like we've done with other memory-amount specific
configs before.
Tested on a generic i12-tvbox with 32 bit bus-width / 1G RAM, and on a
qt840a with 16 bit bus-width / 512M RAM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768
IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP
rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250
accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot,
miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and
3.5mm headphone jack.
More details are available at: http://linux-sunxi.org/Gemei_G9
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Convert GPIO names from Kconfig strings into pin numbers for
the 'ssd2828_config' struct. Add SSD2828 initialization between
enabling the parallel LCD interface and turning on the backlight.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And also add Kconfig option for selecting ELDO3 voltage. The reason
for having this option is that the Android kernel sets ELDO3 to
1.2V when powering up LCD in the case if 'lcd_if' configuration
variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely
to supply power for a SSD2828 chip.
However on the MSI Primo81 tablet, which is using this particular
'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to
be unnecessary and it works regardless. Having no schematics of
this tablet, I can only guess that 1.2V is supplied to SSD2828
in some other way.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Alexey Brodkin
Siarhei Siamashka
Hans de Goede
Michal Suchanek
Paul Kocialkowski
Adam Sampson
Simon Glass
Linus Walleij
Przemyslaw Marczak
Martin Dorwig
Enric Balletbo i Serra
Paul Burton
Siva Durga Prasad Paladugu
Michal Simek
Luka Perkov
tang yuantian
Alison Wang
Xiubo Li
Masahiro Yamada
Ian Campbell
Priit Laes
Aleksei Mamlin