These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
This patch adds whitespace to the printed hex numbers to have an aligned ASCII
printout at the end of the line.
This changes for example the md output from:
---8<---
OMAP3 Tricorder # md.l $loadaddr 5
82000000: 30200109 20a4028c 90010000 08a00000 .. 0... ........
82000010: 01010000 ....
--->8---
to
---8<---
OMAP3 Tricorder # md.l $loadaddr 5
82000000: 30200109 20a4028c 90010000 08a00000 .. 0... ........
82000010: 01010000 ....
--->8---
The cost of this is about 72 byte .text increase (tested with at91 build).
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The "mtest" command is of little practical use (if any), and
experience has shown that a large number of board configurations
define useless or even dangerous start and end addresses. If not even
the board maintainers are able to figure out which memory range can be
reliably tested, how can we expect such from the end users? As this
problem comes up repeatedly, we rather do not enable this command by
default, so only people who know what they are doing will be
confronted with it.
As this changes the user interface, we allow for a grace period
before this change takes effect. For now, we make "mtest"
configurable through the CONFIG_CMD_MEMTEST variable, which is defined
in include/config_cmd_default.h; we also add an entry to
doc/feature-removal-schedule.txt which announces the removal of this
default setting in two releases from now, i. e. with v2013.07.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Do maintain a 200 usecs period of stable power and clock before
asserting the CKE signal and sending commands, have at least 200
DRAM clock cycles pass after initialization before data access.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new mpc5121e based ac14xx board and a new pinmux config
function for setting individual pinmux bit groups. This
function is used in ac14xx board code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Boards may define own IPS divider in the config file if
the default IPS divider doesn't fit their needs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Only define enabled clocks in the config file and enable
the clocks in common code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Remove CSx configurations from board code and only define
required CSx macros in the board config file to configure
chip select windows and parameters.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Currently each mpc512x board has its own LAW and CS config code,
we should avoid this code duplication. Allow all boards to use
common code by only defining LAW and CS config macros like
CONFIG_SYS_CSx_START, CONFIG_SYS_CSx_SIZE and CONFIG_SYS_CSx_CFG.
Also allow common configuration of additional CS parameters by
CONFIG_SYS_CS_ALETIMING, CONFIG_SYS_CS_BURST, CONFIG_SYS_CS_DEADCYCLE
and CONFIG_SYS_CS_HOLDCYCLE options.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds a custom U-Boot command "wdogtoggle" which enables the
external hardware watchdog toggling via an GPIO pin on the a4m2k
board. After issuing this commands, the watchdog will be serviced
by U-Boot so that the user can use all U-Boot commands from the
prompt.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the a4m2k MPC5200B board port. Its a derivate of
the a3m071 board with only minor changes.
Additionally this patch includes some clean-up changes:
- Remove I2C support from a3m071 as its unused
- Fix/enhance default env variables
- Fix some comments
- Add newly introduced CONFIG_SPL_TARGET to automatically build
"u-boot-img.bin"
- Fix dtb patching in READ desciption for SPL Linux booting:
"fdt chosen" needs to get called to patch/create the chosen node.
- Add missing call to spl_board_init():
Define CONFIG_SPL_BOARD_INIT so that spl_board_init() will get
called in the SPL version.
Signed-off-by: Stefan Roese <sr@denx.de>
On MPC5200, the initial RAM (and gd) is located in the internal
SRAM. So we can actually call the preloader console init code
before calling initdram(). This makes serial output (printf)
available very early, even before SDRAM init, which has been
an U-Boot priciple from day 1.
Signed-off-by: Stefan Roese <sr@denx.de>
This is currently set to coreboot.dtsi, but we cannot support this on
old device tree compilers (dtc <= 1.3), so adjust to use ARCH_CPU_DTS
to let the Makefile preprocessor sort this out.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not actually change normal behaviour, but adds a check that
should detect corruption of relocation data (e.g. by using BSS data
prior to relocation).
Also add additional debugging output when enabled.
During this investigation, two situations have been seen:
1. calculate_relocation_address():
uintptr_t size = (uintptr_t)&__bss_end - (uintptr_t)&__text_start;
turns into
111166f: b8 83 c4 17 01 mov $0x117c483,%eax
whih is beyond the end of bss:
0117b484 g .bss 00000000 __bss_end
Somehow the __bss_end here is 255 bytes ahead.
2. do_elf_reloc_fixups():
uintptr_t size = (uintptr_t)&__bss_end - (uintptr_t)&__text_start;
Here the __text_start is 0 in the file:
1111d9f: bb a0 e0 13 01 mov $0x113e0a0,%ebx
1111da4: 81 ef 00 00 00 00 sub $0x0,%edi
As it happens, both of these are in pre-relocation code.
For these reasons we silent check and ignore bad relocations.
Signed-off-by: Simon Glass <sjg@chromium.org>
With CONFIG_OF_CONTROL we may have an FDT in the BSS region. Relocate
it up with the rest of U-Boot to keep the rest of memory free.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present BSS data is including in the image, which wastes binary space.
Remove it by rearranging the sections so that BSS is last.
Signed-off-by: Simon Glass <sjg@chromium.org>
With this symbol we can easy append something (e.g. an FDT) to the U-Boot
binary and access it from within U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to access the timer before U-Boot has relocated
so that we can fully support bootstage.
Add new global_data members to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The memory layout calculations are done in calculate_relocation_address(),
and coreboot has its own version of this function. But in fact all we
really need is to set the top of usable RAM, and then the base version
will work as is.
So instead of allowing the whole calculate_relocation_address() function
to be replaced, create board_get_usable_ram_top() which can be used by
a board to specify the top of the area where U-Boot relocations to.
Signed-off-by: Simon Glass <sjg@chromium.org>
All code related to the bootm ramdisk subcommand is conditionally
enabled by CONFIG_SYS_BOOT_RAMDISK_HIGH except for the help message.
Replace the CONFIG_ARCH defines by CONFIG_SYS_BOOT_RAMDISK_HIGH
to fix this.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
UBI can mount volumes by name or number The current code forces you
to name the volume by prepending every name with "ubi:".
>From fs/ubifs/super.c
* There are several ways to specify UBI volumes when mounting UBIFS:
* o ubiX_Y - UBI device number X, volume Y;
* o ubiY - UBI device number 0, volume Y;
* o ubiX:NAME - mount UBI device X, volume with name NAME;
* o ubi:NAME - mount UBI device 0, volume with name NAME.
Now any name passed in any of the above forms are allowed.
Also update the configs that referenced ubifsmount.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The 'sb' command allows loading files from the host, and listing
directories.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The new 'sb' command is intended to deal with sandbox-specific features
that have no parallel in other archs. This commit adds two sub-commands
to list a directory and read a file from the host filesystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This implementation uses opendir()/readdir() to access the directory
information and then puts it in a linked list for the caller's use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
It doesn't make a lot of sense to have these methods in fs.c. They are
filesystem-specific, not generic code. Add each to the relevant
filesystem and remove the associated #ifdefs in fs.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This allows us to use filesystems on sandbox. It has no effect on other
architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Rather than rely on global variables for the probe functions, pass in
the information that we need filled in. This allows us to potentially
keep the variables private to fs.c in the future, and the meaning of
the probe function is clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
We can use the available methods and avoid using switch(). When the
filesystem is not supported, we fall through to the 'unsupported'
methods: fs_probe_unsupported() prints an error, so the others do
not need to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
There is a structure in fs.c with just a probe method. By adding methods
for other operations, we can avoid lots of #ifdefs and switch()s. As a
first step, create the structure ready for use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This code seems to be entirely othogonal, so remove the #ifdef and put
the condition in the Makefile instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add Bf60x resume from hibernate support
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Spi driver for bf60x is different from old one, so implement a new
driver for it.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Add rsi/sdh support for bf60x.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Board and config header files for bf609-ezkit support.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Stefan Roese
Andreas Bießmann
Wolfgang Denk
Tom Rini
Holger Brunck
Anatolij Gustschin
Simon Glass
Sonic Zhang
Daniel Schwierzeck
Joe Hershberger
Steven Miao
Bob Liu
Scott Jiang
Sonic Zhang