The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The code uses all in all three TMU registers, drop the massive
register layout structures and just define the required timer
registers and use them throughout the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The header contains only the TMU register layout, just inline it
into the TMU timer implementation and drop the header completely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2,
while the old SH parts use CONFIG_SYS_CLK_FREQ directly.
Just put this into the TMU implementation and drop the
CONFIG_SH_TMU_CLK_FREQ config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
These functions are always called for timer = 0, so drop the
timer check. Since these functions are called from one place
only and they are reduced to one line of code, just inline
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The tmu_bit value evaluates to (ffs(4) >> 1) - 1 = (3 >> 1) - 1 = 0.
Just drop the tmu_bit completely as well as CONFIG_SYS_TMU_CLK_DIV.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This constant is always 4 , for all boards that exist. Define it
once in arch/sh/lib/time.c and remove it from the configs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Drop the macro as it is never used and it collides with sh_eth.h macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the macro as it is defined in sh7723.h already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add vbus-supply regulator support.
On some board vbus is not controlled by the phy but by
an external regulator.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
I just stumbled over some cluttered UBIFS messages. It seems some
newline chars are missing in the current U-Boot UBI source.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Last user of this driver went away in May 2017, in
commit eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
When used with a device tree, this will extract the card detect
and write protect pins from the device tree and configure them
accordingly. This assumes the GPIO_ACTIVE_LOW/HIGH is supported
by da8xx_gpio.
Signed-off-by: Adam Ford <aford173@gmail.com>
DM_I2C_COMPAT is somehow being enabled outside of Kconfig, so
this explicitly undefines it in the header file, and brackets
the I2C initialization around an #ifdef to not manually
initialize the I2C controller when the DM_I2C is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_MMC now available, this patch enables DM_MMC for the
omapl138_lcdk in U-Boot and keeps the older style for SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
With CONFIG_BLK becoming a requirement, the Davinci MMC driver
needs to be updated with DM_MMC support. Since SPL is tiny and
many boards do not support DM in SPL, this retains the backwards
compatibility for those boards who need to initialize MMC manually
in SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Signed-off-by: Adam Ford <aford173@gmail.com>
The OF_CONTROL and OF_PLATDATA are not really useful without DM.
This patch supports DM_SPL, but it requires manual references
both Serial and MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
The getcd and getwp functions when DM_MMC is enabled are
assumming the DM_GPIO is enabled. In cases (like SPL) where
DM_GPIO may not be enabled, wrap these calls in an #ifdef
Signed-off-by: Adam Ford <aford173@gmail.com>
The serial port was being manually configured during SPL build,
however in preparation to allow DM in SPL, this needs to change
to be based on whether or not DM_SERIAL is enabled because, soon
the assumption that SPL means no DM may not be accurate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
boot-common.c checks to see if I2C is enabled in SPL, but
it doens't check for DM_I2C before initializing it. This
will now only initialize the I2C is the DM_I2C is not enabled
to avoid initializing it more than once.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Platforms with limited resources in SPL may enable OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
The driver was developed with references for more than just
dra7, but never included. At least for omap3, this appears
to be functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPIO bank numbers do not appear in the device tree, so this
patch makes the gpio name based on the address
(ie gpio@49054000_31 vs gpio4_31)
adam
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With the re-sync from Linux 4.18, several entries in
da850-evm-u-boot.dtsi are no longer necessary, so this patch
removes them.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM and device tree support, let's use the GPIO_ACTIVE_HIGH
and GPIO_ACTIVE_LOW from the device tree as they are intended.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPIO banks are broken up into two 16-bit registers for each
bank set. Unfortunately, the math that determines how to shift
blindly shifted by the number of the gpio. This worked for gpio
numbers under 32, but higher gpio's are broken. This fixes the
gpio index, so the bank is passed and the shift amount within
the register is passed now instead of the gpio number.
Fixes: 8e51c0f25406("dm: gpio: Add DM compatibility to
GPIO driver for Davinci")
Signed-off-by: Adam Ford <aford173@gmail.com>
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
At least for now, CONFIG_BLK is working, but this variant of
the da850evm doesn't need/support SPL so it's OK to enable it
here.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Create a basic U-Boot environment that allows the automatic loading
of a Linux Kernel located at /boot/Image and an associated device tree
blob located at /boot/k3-am654-base-board.dtb from the secondary
partition of an ext4-formatted SD card on the AM654x EVM. Furthermore
the boot.scr and uEnv.txt detection and loading schemes are supported
in a manner already known from other TI platforms.
Note that this is intended to be a starting point to enable initial
board use and will most certainly get extended and refactored as
different boot media become available.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tom Rini
Marek Vasut
Patrice Chotard
Stefan Roese
Tuomas Tynkkynen
Adam Ford
Lokesh Vutla
Andreas Dannenberg