The address of the I2C TPM is now defined in the device tree so there is no
need for the CONFIG options.
Remove them from the README and board config to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is not used anymore by any board so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If board uses downstream Chrome OS U-Boot as first stage
bootloader and upstream version is chained second stage,
1.1V is minimum voltage borderline.
Signed-off-by: Misha Komarovskiy <zombah@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make "Generic Driver Options" menu show on the top in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add Kconfig entries for the simple-bus driver, both for U-Boot
and for SPL. The simple-bus is enabled by default in U-Boot and
disabled by default in SPL to preserve the original behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Modified to fit on top of Masahiro's $(SPL) setup:
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This can be simply written with list_for_each_entry(), maybe
this macro was not necessary in the first place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Initial version of DTSI for ProXstream2 and PH1-LD6b and DTS for
PH1-LD6b reference board.
Import from Linux with some adjustments:
- Use SPDX-License-Identifier
- Add clock-frequency to serial nodes
- Drop unusable nodes from -ref.dts
While I am here, sort Makefile entries alphabetically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initial version of UniPhier PH1-Pro5 device tree.
(Imported from Linux with adjustment for SPDX License Identifier)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit imports device tree updates from Linux. It eventually
adds pinctrl-related nodes and properties.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is enabled only for UniPhier SoCs and ARCH_UNIPHIER now
selects OF_CONTROL and SPL_OF_CONTROL.
This driver no longer needs to support platform data configuration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Device Tree really improves code maintainability and is now
available for SPL too.
This is the state-of-the-art implementation in U-boot.
The board files (platform data) are no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 2580a2a7e7 ("mtd: nand: Increase max sizes of OOB and
Page size"), three boards (ph1_ld4, ph1_pro4, ph1_sld8) fail to build
with the following error message:
arm-linux-gnueabi-ld.bfd: SPL image plus BSS too big
They compile drivers/mtd/nand/denali_spl.c and it has a page_buffer
as static data:
static uint8_t page_buffer[NAND_MAX_PAGESIZE];
This buffer required 8KB in .bss section before that commit and now
it has been increased to 16KB. Given limited code/memory size for SPL,
it is not a good idea to allocate a page buffer statically. In the
first place, the load address 'dst' can be used as a page buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Otherwise we get:
tools/atmelimage.c:134:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘size_t’ [-Wformat=]
debug("atmelimage: interrupt vector #%d is 0x%08X\n", pos+1,
^
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have separate function to enable USB clocks, remove
enabling USB clocks from enable_basic_clocks(). Now board_usb_init()
should take care to invoke enable_usb_clocks() for enabling
USB clocks.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
invoke enable_usb_clocks during board_usb_init and disable_usb_clocks
during board_usb_exit to enable and disable clocks respectively.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in omap5 board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in beagle_x15 board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The usbboot environment variable has 'usb start' command but
doesn't have the corresponding 'usb stop' command. This breaks
usb peripheral mode if tried after 'run usbboot' fails to load
the images in usb host mode.
Fix it here by adding 'usb stop' command in usbboot env.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
vbus_id_status is initialized in board_usb_init. So remove it
while creating dwc3_device objects.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added support to power on/power off the second USB PHY present in
DRA7xx and AM57xx.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Writing "0x00" to the USBOTGSS_IRQENABLE_SET_MISC and
USBOTGSS_IRQENABLE_SET_0 doesn't disable the interrupts. Used
USBOTGSS_IRQENABLE_CLR_MISC and USBOTGSS_IRQENABLE_CLR_0 instead.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SOURCE_DATE_EPOCH mechanism for reproducible builds require some date(1)
with -d switch to print the relevant date and time strings of another point of
time.
In other words it requires some date(1) that behaves like the GNU date(1) [1].
The BSD date(1) [2] on the other hand has the same switch but with a different
meaning.
Respect this and check the date(1) abilities before usage, error on non
working version. Use the well known pre- and suffixes for the GNU variant of
a tool on *BSD hosts to search for a working date(1) version.
[1] http://man7.org/linux/man-pages/man1/date.1.html [2]
http://www.freebsd.org/cgi/man.cgi?query=date
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Commit 181bd9dc61 introduced Kconfig selection
for SYS_PROMPT. When applying the new picosam9g45 board this change slipped
through, adopt it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This fixes the following genboardscfg.py warnings:
---8<---
WARNING: no status for 'at91sam9g20ek_2mmc'
WARNING: no maintainers for 'at91sam9g20ek_2mmc'
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This fixes following genboardscfg.py warning:
---8<---
WARNING: no status for 'at91sam9rlek_mmc'
WARNING: no maintainers for 'at91sam9rlek_mmc'
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The SYS_BOOT-based fallback shouldn't only check for one of the conditions of
use and then let the switch/case handle each boot device without enforcing the
conditions for each type of boot device again.
For instance, this behaviour would trigger the fallback for UART when
BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should
be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not
CONFIG_SPL_USB_SUPPORT.
Separating the logic for USB and UART solves this.
In addition, this adds support for more peripheral devices (USBETH and CPGMAC)
to the fallback mechanism. Note that the USBETH boot device should always be
different from the USB boot device (each should match a different bootrom
handoff case).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch brings the following changes to the x600 board support:
- Add USB EHCI support
- Add VFAT support for USB key file access
- Increase malloc size (for UBI / UBIFS usage)
- Enable Thumb mode to save some image space
- Remove unreferenced CONFIG_STACKSIZE
- Remove unreferenced CONFIG_SPL_NO_PRINTF
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
The designware ethernet driver supports d-cache now. So there is nothing
stopping us now to enable the caches completely on SPEAr.
Tested on SPEAr600 x600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
The SPL implementation for SPEAr600 is older than the common SPL
infrastructure. This patch now moves the SPEAr600 SPL over to the
common SPL code.
Tested on the only SPEAr board that currently uses SPL in mainline
U-Boot, the x600.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Booting SPEAr600 eval board doesn't work with current mainline U-Boot. With
this patch the low-vector bit is left to '0'. Resulting in the common
relocation of the vectors to 0 (SDRAM) to work correctly.
Tested on the SPEAr600 EVB.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
ARM supported speeds and init value of core_pll for SDP1200
are programmed wrong as part for the device speed cleanups.
Fixing it here.
Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue
Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection")
Tested-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MLO(NAND/MMC boot image), is used for all the ks2 platforms.
Enabling it in config.mk so that these images will be automatically
built upon calling make. u-boot-spi.gph is already the build target,
so not including here.
Reported-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
NAND boot mode, ROM expects an image with a gp header in the
beginning and an 8bytes filled with zeros at the end. The same is
true for SD boot on K2G platforms but the file name should be MLO.
Renaming u-boot-nand.gph to MLO, so that same image can be used for
NAND and SD boots. And also not including all the u-boot only images
under CONFIG_SPL_BUILD.
Reported-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone has build rules introduced by commit ef509b9063 ("k2hk: add
support for k2hk SOC and EVM") and commit 0e7f2dbac6 ("keystone: add
support for NAND gpheader image").
These are not reused by other platforms for the build, hence there is no
clear benefit is maintaining them in the generic makefile as a build
target. move these to the keystone specific make option
Original idea of using config.mk by Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently u-boot stack is defined at the beginning of MSMC RAM.
This is a problem for uart boot mode as ROM downloads directly to
starting of MSMC RAM.
Fixing it by moving stack to the end of u-boot section and shifting
SYS_TEXT_BASE to the start of MSMC RAM.
Updated division of MSMC RAM is shown below:
-----------------------------------------
| | | |
| U-Boot text |U-Boot | SPL text |
| download | Stack | Download + |
| | | SPL_BSS + |
| | | SPL_STACK |
-----------------------------------------
[1] [2] [3] [4]
[1] SYS_TEXT_BASE (Start of MSMC RAM)
[2] SPL_TEXT_BASE - GBL_DATA_SIZE
[3] SPL_TEXT_BASE
[4] END of SPL
[1] + [2] is at least 1M on all platforms, so no chance of overlap.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The set_default_env() function from env_common.c expects either
a fully formatted error msg, e.g.: "## Resetting to default environment\n"
or an error msg prefixed with an !, in which case it will format it.
Fix the init_mmc_for_env() error messages to be prefixed with a !
this changes the bootup-log on sunxi when no mmc card is found from:
MMC: SUNXI SD/MMC: 0
No MMC card foundIn: serial
Out: serial
To:
MMC: SUNXI SD/MMC: 0
*** Warning - No MMC card found, using default environment
In: serial
Out: serial
Which clearly is how things should look.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This should use the align parameter, not bytes. Natural alignment is one
use case but should not be the only one supported by this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Corresponds to ba71a0e (Fix _parse_block() 'parent' documentation re.
ifs.) from upstream, just adding the SPDX tag.
Has performance improvements, code cleanup, Python 3 support, and various
small fixes, including the following:
- Unset user values when loading a zero-byte .config. (5e54e2c)
- Ignore indented .config assignments. (f8a7510)
- Do not require $srctree to be set for non-kernel projects. (d56e9c1)
- Report correct locations in the presence of continuation lines.
(0cebc87)
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Simon Glass
Misha Komarovskiy
Bin Meng
Marek Vasut
Masahiro Yamada
Tom Rini
Kishon Vijay Abraham I
Andreas Bießmann
Paul Kocialkowski
Marcel Ziswiler
Stefan Roese
Lokesh Vutla
Nishanth Menon
Hans de Goede
Ulf Magnusson