This change fixes the compiler warning
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF
for correct output!
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch re-formats the arm920t s3c24x0 header files in preparation for
changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patch 1/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This sets CONFIG_SYS_HZ to 1000 for all boards that use the s3c2400 and
s3c2410 cpu's which fixes various problems such as the timeouts in tftp being
too short.
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't
have any s3c2400 or s3c2410 boards but need this patch applying before I can
submit patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets
and no new warnings or errors were found.
It was originally submitted on 21/06/2009 but didn't get into the 2009.08
release, and Jean-Pierre made one comment on the original patch (see
http://lists.denx.de/pipermail/u-boot/2009-July/055470.html). I've made two
changes to the original patch:
- it's been re-based to the current release
- I've re-named get_timer_raw() to get_ticks() in response to Jean-Pierre's comment
This affects the sbc2410, smdk2400, smdk2410 and trab boards. I've copied it
directly to the maintainers of all except the sbc2410 which doesn't have an
entry in MAINTAINERS.
Signed-off-by: Kevin Morfitt <kmorfitt@aselaptop-1.localdomain>
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch includes the serial driver for s5pc1xx.
s5pc1xx uart driver needs own register setting and clock configuration.
So, need to special driver.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch includes the onenand driver for s5pc100
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds support for the Samsung s5pc100 and s5pc110
SoCs. The s5pc1xx SoC is an ARM Cortex A8 processor.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch implements several updates:
-disable CONFIG_ENV_OVERWRITE
-add new hardware style variants and set the arch numbers appropriate
-pass the serial# and hardware revision to the kernel
-removed unused macros from include/configs/meesc.h
-fixed multiline comment style
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This changes fixes an early i2c error.
It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.
While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.
Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.
Run tested on Beagle.
Compile tested on the omap3's
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Some DaVinci SOC's use GPIOs to enable EMAC and DM9000.
This patch adds some definitions for GPIO registers and also adds
structures for GPIO.
A separate header file is being added so that in future we
can have a DaVinci GPIO driver similer to OMAP.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
In the DaVinci specific code, we use both CONFIG_SOC_DM646X and
CONFIG_SOC_DM646x to represent DM646x specific code.
This patch changes occurrences of CONFIG_SOC_DM646x to
CONFIG_SOC_DM646X. This is because for DM644x series of SOCs we use
the flag CONFIG_SOC_DM644X. We want some uniformity.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag.
This is already included when we include the
config_cmd_default.h header file. So this flag is removed.
Also another flag to enable NAND functions was being
enabled incorrectly.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch does the following
1) Enables the NAND driver which is now available.
2) Enables the 'CONFIG_MTD_DEVICE' as without this the
compilation will fail
3) We now have a safe place to store environment and defines
an offset where this can be stored. This offset value is such that it is after
the location where U-Boot is flashed using TI flash utilities.
4) Enables Bootdelay
5) Increases malloc() arena size. Manufacturers are coming out with
NAND with large blocks sizes of upto 1 MiB. It has been noticed that
as the block size of the NAND used is increased, if this particular
value is not increased, the NAND driver will output out of memory
errors.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
DM646x is an SOC from TI which has both an ARM and a DSP.
There are multiple variants of the SOC mainly dealing with different
core speeds.
This patch adds the initial framework for the DM646x SOC.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The Default mode that is built for the Davinci DVEVM happens
to be the NOR mode.
When we want to build for the NAND mode, we get a compilation
error. This is overcome by defining the CONFIG_MTD_DEVICE
flag in the NAND mode.
The image built for NAND mode was successfully tested on the
DaVinci DM6446 EVM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
v7_flush_dcache_all, because it depends on omap ROM code is not
generic. Rename the function to 'invalidate_dcache' and move it
to the omap cpu directory.
Collect the other omap cache routines l2_cache_enable and
l2_cache_disable with invalide_dcache into cache.S. This
means removing the old cache.c file that contained l2_cache_enable
and l2_cache_disable.
The conversion from cache.c to cache.S was done most through
disassembling the uboot binary. The only significant change was
to change the comparision for the return of get_cpu_rev from
cmp r0, #0
beq earlier_than_label
Which was lost information to
cmp r0, #CPU_3XX_ES20
blt earlier_than_label
The paths through the enable routine were verified by
adding an infinite loop and seeing the hang. Then
removing the infinite loop and seeing it continue.
The disable routine is similar enough that it was not
tested with this method.
Run tested by cold booting from nand on beagle and zoom1.
Compile tested on MAKEALL arm.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch removes the asm/sizes.h header file from being
included in the DaVinci SOC configs.
References to SZ_xx have been replaced by appropriate
bit shifted values.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Wolfgang Denk <wd@denx.de>
This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.
The driver requires that the following macros should be defined into the board
configuration file:
CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support
If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:
MII_INIT - Generic code to enable the MII bus (optional)
MDIO_DECLARE - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ - Read the MDIO pin
MDIO(v) - Write v on the MDIO pin
MDC_DECLARE - Declaration needed to access to the MDC pin (optional)
MDC(v) - Write v on the MDC pin
The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).
When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):
char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)() - Write the MDIO pin
int (*get_mdio)() - Read the MDIO pin
int (*set_mdc)() - Write the MDC pin
int (*delay)() - Delay function
void *priv - Private data used by board specific code
The board code will look like:
struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
{ .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
sizeof(bb_miiphy_buses[0]);
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.
The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file. The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>
Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 054197ba and later fixes used an array to initialize some of
the MDDRC parameters; however, the use of an array turned out to be a
bad idea as it was not possible to correlate structure entries to
array indices in readable and reliable way. Now we use a struct
instead, which makes this self-explanatory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
After running checkstyle.pl on the three previous patches I noted that in
the *.h files there were a lot of long lines. This patch solves this problem.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Here you find all the changes in the include directory for new register names
and adapting other ones to the names used by AMCC in their manuals, e.g.
For 440EPx/GRPPC440EPx/GRX, Revision 1.15 – September 22, 2008
For PPC405GP Embedded Processor, Revision 1.02 – March 22, 2006
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Unfortunately some Rev D PPC405EX/405EXr PVR's are identical with older
405EX(r) parts. Here a list:
0x12911475 - 405EX Rev D with Security *and* 405EX Rev A/B witout Sec
0x12911473 - 405EX Rev D without Security *and* 405EXr Rev A/B with Sec
Since there are only a few older parts in the field, this patch now
changes the PVR's above to represent the new Rev D versions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phong Vo" <pvo@amcc.com>
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The random_port() is meant to be used by other net code, but without a
prototype, we get fun warnings like:
dns.c: In function 'DnsSend':
dns.c:89: warning: implicit declaration of function 'random_port'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Now that proper relocation is supported, the reloc_off field is no longer
necessary.
Note that the location of the standalone application jump table pointer
in the global data structure is affected by this change, breaking
execution of standalone applications compiled for previous versions of
U-Boot.
We therefore increment XF_VERSION to 6
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
These architectures don't need relocation fixups, so reduce their
codesize a bit by defining CONFIG_RELOC_FIXUP_WORKS.
Also remove the reloc_off field from their global data structures
as it is no longer needed.
Note that the location of the standalone application jump table pointer
in the global data structure is affected by this change, breaking
execution of standalone applications compiled for previous versions of
U-Boot. We will therefore increment XF_VERSION in the next commit,
which also touches this area.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add #ifdefs where necessary to not perform relocation fixups. This
allows boards/architectures which support relocation to trim a decent
chunk of code.
Note that this patch doesn't add #ifdefs to architecture-specific code
which does not support relocation.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
PPC boards are the only users of the current FPGA code which is littered
with manual relocation fixups. Now that proper relocation is supported
for PPC boards, remove FPGA manual relocation.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds support to detect the amount of DDR2 SDRAM
on PMC440 modules. Detection is done by probing through
a list of available and supported hardware configurations
from 1GByte down to 256MB.
The static TLB entry is replaced by dynamically created entries.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch merges the ECC handling (ECC parity byte writing) into one
file (ecc.c) for all PPC4xx SDRAM controllers except for PPC440EPx/GRx.
This exception is because only those PPC's use the completely different
Denali SDRAM controller core.
Previously we had two routines to generate/write the ECC parity bytes.
With this patch we now only have one core function left.
Tested on Kilauea (no ECC) and Katmai (with and without ECC).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Felix Radensky <felix@embedded-sol.com>
Cc: Grant Erickson <gerickson@nuovations.com>
Cc: Pieter Voorthuijsen <pv@prodrive.nl>
Reorganize DDR2 ECC handling to use common code for
SPD DIMMs and soldered SDRAM. Also, use common code
to display SDRAM info (ECC, CAS latency) for SPD and
soldered SDRAM variants.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Linux kernel has changed the way it numbers serial ports, so update
the default command line to match it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The u-boot image has outgrown the current space and overflowed into the
env sector. So move the env to the next available sector (we've already
allocated the first few sectors anyways for u-boot).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.
The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.
The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.
This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.
When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.
This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.
Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By nature of being based off the MPC8548CDS board, this
board inherited an ENV_SIZE setting of 256k. But since
it has a smaller flash device (8MB soldered on), it has
a native sector size of 128k, and hence the ENV_SIZE was
causing 2 sectors to be used for the environment.
By removing the unused sector, we can push TEXT_BASE up
closer to the end of address space and reclaim that
sector for any other application. This also fixes the
mismatch between TEXT_BASE and MONITOR_LEN reported by
Kumar earlier.
Since this board also supports the ability to boot off
the 64MB SODIMM flash, this change is forward looking
with that in mind; i.e. the settings for MONITOR_LEN
and ENV_SIZE will work when the 512k sectors of the
SODIMM flash are used for alternate boot in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Converted all white space to tabs
* Converted all types to u8/u16/u32
* Reduce lines to fit in 80 columns
* Renamed MPC85xx_{Q,B}MAN -> FSL_CORENET_{Q,B}MAN
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The latest PPC4xx register cleanup patch missed some SDRAM defines.
This patch now changes lower case UIC defines to upper case. Also
some names are changed to match the naming in the IBM/AMCC users
manuals (e.g. mem_mcopt1 -> SDRAM0_CFG).
Signed-off-by: Stefan Roese <sr@denx.de>
The latest PPC4xx register cleanup patch missed the UIC defines.
This patch now changes lower case UIC defines to upper case.
Signed-off-by: Stefan Roese <sr@denx.de>
Eric Benard
kevin.morfitt@fearnside-systems.co.uk
Minkyu Kang
Daniel Gorsulowski
Olof Johansson
Tom Rix
Sandeep Paulraj
Dirk Behme
Simon Kagstrom
Luigi 'Comio' Mantellini
Detlev Zundel
Wolfgang Denk
Niklaus Giger
Stefan Roese
Ben Warren
Mike Frysinger
Peter Tyser
Matthias Fuchs
Felix Radensky
Mingkai Hu
Paul Gortmaker
Kumar Gala