Only A23/A33 in SUN8I want a default value of CONS_INDEX of 5, for other
chips the default value is 1 like other Allwinner SoCs.
Fix this default value.
The original wrong value has lead to wrong console on H3 Orange Pi
boards.
Fixes: 7095f86418 ("sunxi: Convert CONS_INDEX to Kconfig")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If current_urb is NULL it should not be dereferenced.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not condition the compilation of the U_BOOT_DRIVER by !OF_PLATDATA.
This is inconsistent with the majority of other drivers. This also
blocks OF_PLATDATA boards with an 16550-compatible serial from using
serial in SPL.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added tweak for rock to avoid a TPL build failure:
Signed-off-by: Simon Glass <sjg@chromium.org>
I don't have the hardware test this, but it is almost certainly a typo
in the code dating back to at least 2004.
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Add a specific serial driver for Intel MID platforms.
It has special fractional divider which can be programmed via UART_PS,
UART_MUL, and UART_DIV registers.
The UART clock is calculated as
UART clock = XTAL * UART_MUL / UART_DIV
The baudrate is calculated as
baud rate = UART clock / UART_PS / DLAB
Initialize fractional divider correctly for Intel Edison platform.
For backward compatibility we have to set initial DLAB value to 16
and speed to 115200 baud, where initial frequency is 29491200Hz, and
XTAL frequency is 38.4MHz.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add separate enable/disable controls for driver-model serial. While this
is generally enabled in SPL it may not be in TPL, since serial output can
be obtained with the debug UART with minimal code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree support for stm32f7 serial driver & removes serial
platform data structure.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add i.MX7ULP support.
The buadrate calculation on i.MX7ULP is different,so add a new setbrg
function for i.MX7ULP.
Add a enum lpuart_devtype for runtime check for different platforms.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add necessary structs to have the driver also work for the serial
on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no CONFIG_OF_PLATDATA, only CONFIG_SPL_OF_PLATDATA, so rename
the two references to CONFIG_OF_PLATDATA to CONFIG_SPL_OF_PLATDATA.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add compatibility string for the Ingenic JZ4780 SoC, the necessary
UART enable bit into FCR and register shift. Neither are encoded
in the DTS coming from Linux, so we need to support it this way.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver data to each compatible string to identify the type of
the port. Since all the ports in the driver are entirely compatible
with 16550 for now, all are marked with PORT_NS16550. But, there
are ports which have specific quirks, like the JZ4780 UART, which
do not have any DT property to denote the quirks. Instead, Linux
uses the compatible string to discern such ports and enable the
necessary quirks.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Add function which allows fetching the default FCR register setting
from platform data for DM , while retaining old behavior for non-DM
by returning UART_FCRVAL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
This is not used by any boards. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For the Raspberry Pi 3 it needs to be possible to disable the serial
device after initialization happens, as only after the GPIO device is available
it is known whether the mini uart is usable.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To be able to represent the skip-init platdata element with OF_CONTROL,
it needs to be read from the device tree as well and put into the platform data.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device tree support for the bcm283x mini-uart driver.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Migrate the PXA serial driver to be configured via Kconfig.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
It's not always true that LPUART clock is CONFIG_SYS_CLK_FREQ. This
patch provides a weak function get_lpuart_clk(), so that the clock
can be ovreridden on a specific board which uses different clock
for LPUART.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Reformat commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add support to enable an early debug UART for debugging.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add ATMEL_USART option to support to enable the Atmel usart driver
from Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This converts the following to Kconfig:
CONFIG_SYS_STDIO_DEREGISTER
This option should never be enabled in SPL, so use
CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit 82f5279b0c.
The build failure of k2*evm boards was fixed in a different way by
the previous commit. It is nasty to patch generic drivers around
with #ifdef CONFIG_CLK just for the KeyStone's matter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When calling clk_get_by_index(), fall back to the legacy method of
getting the clock if -ENOENT is returned.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The Armada 3700's UART is a simple serial port. It has a 32 bytes
Tx FIFO and a 64 bytes Rx FIFO integrated. This patch adds support
for this UART including the DEBUG UART functions for very early
debug output.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Previously ns16550 compatible UARTs probed via device tree have needed
their device tree nodes to contain a clock-frequency property. An
alternative to this commonly used with Linux is to reference a clock via
a phandle. This patch allows U-Boot to support that, retrieving the
clock frequency by probing the appropriate clock device.
For example, a system might choose to provide the UART base clock as a
reference to a clock common to multiple devices:
sys_clk: clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <10000000>;
};
uart0: uart@10000000 {
compatible = "ns16550a";
reg = <0x10000000 0x1000>;
clocks = <&sys_clk>;
};
uart1: uart@10000000 {
compatible = "ns16550a";
reg = <0x10001000 0x1000>;
clocks = <&sys_clk>;
};
This removes the need for the frequency information to be duplicated in
multiple nodes and allows the device tree to be more descriptive of the
system.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.
However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.
This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.
That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is very likely to be necessary for normal use cases.
Set its default to 'y' for shorter defconfig files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
BLANCHE is development board based on R-Car V2H SoC (R8A7792)
This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This can be used in the same way as other R-CAR serial setting.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read information about clock frequency from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Commit 83fd908f28 ("dm: imx: serial: Support DTE mode when using driver
model") breaks the serial output for the imx boards that do not use
the serial driver model.
The reason for the breakage is that it's setting UFCR_DCEDTE
unconditionally for the non-dm case.
So keep the original behavior by removing UFCR_DCEDTE setting in the
non-dm case.
Tested on mx7sabresd and mx6wandboard.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The MXC UART IP can be run in DTE or DCE mode. This depends on the
board wiring and the pinmux used and hence is board specific. This
extends platform data with a new field to choose wheather DTE
mode shall be used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Icenowy Zheng
Mylène Josserand
xypron.glpk@gmx.de
Alexandru Gagniuc
Alyssa Rosenzweig
Andy Shevchenko
Simon Glass
Tom Rini
Philipp Tomsich
Sébastien Szymanski
Vikas Manocha
Peng Fan
Heiko Stübner
Patrice Chotard
Stefan Herbrechtsmeier
Heiko Schocher
Marek Vasut
Patrick Bruenn
Fabian Vogt
Marcel Ziswiler
Shaohui Xie
Wenyou Yang
Jagan Teki
Masahiro Yamada
Stefan Agner
Alexandre Courbot
Stefan Roese
Paul Burton
Alexander Graf
masakazu.mochizuki.wd@hitachi.com
Hiroyuki Yokoyama
Michal Simek
Breno Lima