Use two separate partitions for the two firmware instances. Also
resize them to be of the same size which also makes the start of
the UBI partition nicely aligned to 0x400000.
In order to detect the new MTD layout and whether we run a U-Boot
with the new BCB format or not, introduce a variable called
"updlevel" which we can use in update/upgrade scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Use device-tree fixup to communicate the MTD partitions to the
kernel. Remove mtdparts from the kernel command line.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Implement board level USB PHY mode callback. On USB OTG Port 1
the Colibri standard foresees GPIO USBC_DET to decide whether the
port should run in Host or Device mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Limit memory used for relocation of FDT or initrd. This is
required to make sure that relocated artifacts are within lowmem.
If fdt_high or initrd_high are not set, U-Boot automatically
relocates artifacts to the end of memory. But this area won't
be part of lowmem and hence will not be accessible by the kernel
during early boot.
With VM split set to 2G/2G (i.MX default), only the 2GB Apalis
iMX6 is affected by that issue. With VM split set to 3G/1G (ARM
default) also modules with 1GB of memory are affected. With the
latter the amount of lowmem will be 760MiB.
The value must also not exceed available memory! Use a safe value
of 512MiB for Apalis and 256MiB for Colibri.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Device tree overlays might prove useful in the future, enable it
by default on all Toradex modules.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
All modules use the common g_dnl_bind_fixup implementaton which
calculates the PID according to product id (read from the config
block) plus offset of 0x4000. In case there is no config block
support (e.g. SPL) or in case the config block is not readable,
fall back to a generic product id (product id 0, which can be
interpreted as "Unknown Module").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
According to the MX7D fuse map the following speed grades are available:
800 MHz
500 MHz
1000 MHz
1200 MHz
So simply return the real frequency that corresponds to the speed grade.
With this change we see on boot:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the MX7D fuse map the speed grade of the parts, which
return '1' is 500MHz instead of 850MHz, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This is needed to make the UMS command work again as it fails with the
following error:
BIOS> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000
g_dnl_register: failed!, error: -19
ERROR: g_dnl_register failed
at cmd/usb_mass_storage.c:179/do_usb_mass_storage()
That's because usb_setup_ehci_gadget() function is looking for the usb
device using the req_sed number.
This change makes the usb device have a req_seq number and the UMS
command work again:
BIOS> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000
CTRL+C - Operation aborted
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM
Since The module will use the same devicetree, we patch
the ram size in ft_board_setup.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
We have a Kconfig name for the module types. Let's Use it.
Some feature selections and configurations are based on the
module. Module selection selects the CPU type.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot based
on the bootdevice so-that conditional macros for MMC via
CONFIG_BOOTCOMMAND should be avoided in config files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21)
Trying to boot from MMC2
U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Net: No ethernet found.
Hit any key to stop autoboot: 0
Booting from mmc ...
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since the CS are not in use, do not map them. User of starterkit
mainboard is free to use them otherwise. When using these pins later
in the OS for instance as GPIO IRQ pin, they need to be input.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
The current driver stength is too high, leading to spec violations
on the falling edge. Fix it with values from HW
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Use meaningful macros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
BOOT_CFG1[7:4] the NAND boot mode selection is done
only when BOOT_CFG1[7] is 1 hence update the NAND
boot mode detection bit case. This information available
on Table 8-11. NAND Boot eFUSE Descriptions, from IMX6DQRM.
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
dts files related to i.MX6 engicam boards are maintined
under board, so include them under board/engicam/*/MAINTAINERS
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tim Harvey
Stefan Agner
Fabio Estevam
Sébastien Szymanski
Lukasz Majewski
Markus Niebel
Jagan Teki
Jagan Teki