Add support for interlaced modes, this is a preparation patch for adding
composite out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We should only subtract 2 from the vblank time when using tcon1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All the #ifdef-ery in selecting the default and fallback monitor type is
becoming unyielding and makes the code hard to read, replace it with a few
helper functions.
This will also be useful with the upcoming CHIP board which has display
adapter daughterboards which should be runtime detectable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Jesurun Q5 has the musb hooked up to an usb-a receptacle, enable it
in host-only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Do not add a bogus (pointing to a non existing serial port) stdout-path
alias to dts on boards without a serial port.
Note that we still define CONS_INDEX as this is used by the SPL where we do
not use DM_SERIAL and thus CONFIG_REQUIRE_SERIAL_CONSOLE is not honored.
We are getting away with this because the sun5i die actually has
an uart0, which in the A13 package is not routed to the outside,
so we are simply sending SPL bootup messages to the tx pin at the
edge of the die, and they go no further from there...
And sofar we only have one A13 board which does not have a serial
port, all others do have a serial port. This kinda makes sense since
the A13 is a much lower pincount package compared to all the other
sunxi SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we have code to check the id-pin and detect usb-host adapters
plugged into the otg port that way, enable it on the tablets which I own.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enable the otg/drc usb controller on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
P2371-0000 is a P2581 or P2530 CPU board married to a P2595 I/O
board. The combination contains SoC, DRAM, eMMC, SD card slot,
HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
a GPIO expansion header, and an analog audio jack.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
E2220-1170 is a Tegra210 bringup board with onboard SoC, DRAM,
eMMC, SD card slot, HDMI, USB micro-B port, and sockets for various
expansion modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_MAX77620_POWER isn't used anywhere. Don't define it in p2571.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.
Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-boot is responsible for enabling the GPU DT node after all necessary
configuration (VPR setup for T124) is performed. In order to be able to
check whether this configuration has been performed right before booting
the kernel, make it happen during board_init().
Also move VPR configuration into the more generic gpu.c file, which will
also host other GPU-related functions, and let boards specify
individually whether they need VPR setup or not.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a comment block to the top of each generated Tegra pinmux header file
indicating that the file was auto-generated, should not be manually
edited, and with a pointer to the tool and command used to generate it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Additionally, ARM64 devices typically run a secure monitor in EL3 and
U-Boot in EL2, and set up some secure RAM carve-outs to contain the EL3
code and data. These carve-outs are located at the top of 32-bit address
space. Restrict U-Boot's RAM usage to well below the location of those
carve-outs. Ideally, we would the secure monitor would inform U-Boot of
exactly which RAM it could use at run-time. However, I'm not sure how to
do that at present (and even if such a mechanism does exist, it would
likely not be generic across all forms of secure monitor).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present lower case is used for the regulator names in the device tree.
The kernel uses upper case and U-Boot will require this also since it will
move to a case-sensitive name check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the debug UART and emit a single 'a' early in the init sequence to
show that it is working.
Unfortunately the debug UART implementation needs a stack to work. I cannot
seem to remove this limitation as the absolute 'jmp %eax' instruction goes
off into the weeds.
So this means that the character output cannot be any earlier than
car_init_ret, where memory is available for a stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Some devices are bound entirely by probing and do not have the benefit of
a device tree to give them a name. This is very common with PCI and USB. In
most cases this is fine, but we should add an official way to set a device
name. This should be called in the device's bind() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This should be used for sandbox. We can convert at least one driver to use
it, but in the meantime, enable the feature so that the code is
build-tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
This new command can dump all device resources associated to
each device. The fields in every line shows:
- The address of the resource
- The size of the resource
- The name of the release function
- The stage in which the resource has been acquired (BIND/PROBE)
Currently, there is no driver using devres, but if such drivers are
implemented, the output of this command should look like this:
=> dm devres
- root_driver
- soc
- extbus
- serial@54006800
bfb541e8 (8 byte) devm_kmalloc_release BIND
bfb54440 (4 byte) devm_kmalloc_release PROBE
bfb54460 (4 byte) devm_kmalloc_release PROBE
- serial@54006900
bfb54270 (8 byte) devm_kmalloc_release BIND
- gpio@55000000
- i2c@58780000
bfb5bce8 (12 byte) devm_kmalloc_release PROBE
bfb5bd10 (4 byte) devm_kmalloc_release PROBE
- eeprom
bfb54418 (12 byte) devm_kmalloc_release BIND
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, Devres requires additional 16 byte for each allocation,
which is not so insignificant in some cases.
Add CONFIG_DEVRES to make this framework optional.
If the option is disabled, devres functions fall back to
non-managed variants. For example, devres_alloc() to kzalloc(),
devm_kmalloc() to kmalloc(), etc.
Because devres_head is also surrounded by an ifdef conditional,
there is no memory overhead when CONFIG_DEVRES is disabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
devm_kmalloc() is identical to kmalloc() except that the memory
allocated with it is managed and will be automatically released
when the device is removed/unbound.
Likewise for the other variants.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
In U-Boot's driver model, memory is basically allocated and freed
in the core framework. So, low level drivers generally only have
to specify the size of needed memory with .priv_auto_alloc_size,
.platdata_auto_alloc_size, etc. Nevertheless, some drivers still
need to allocate/free memory on their own in case they cannot
statically know the necessary memory size. So, I believe it is
reasonable enough to port Devres into U-boot.
Devres, which originates in Linux, manages device resources for each
device and automatically releases them on driver detach. With devres,
device resources are guaranteed to be freed whether initialization
fails half-way or the device gets detached.
The basic idea is totally the same to that of Linux, but I tweaked
it a bit so that it fits in U-Boot's driver model.
In U-Boot, drivers are activated in two steps: binding and probing.
Binding puts a driver and a device together. It is just data
manipulation on the system memory, so nothing has happened on the
hardware device at this moment. When the device is really used, it
is probed. Probing initializes the real hardware device to make it
really ready for use.
So, the resources acquired during the probing process must be freed
when the device is removed. Likewise, what has been allocated in
binding should be released when the device is unbound. The struct
devres has a member "probe" to remember when the resource was
allocated.
CONFIG_DEBUG_DEVRES is also supported for easier debugging.
If enabled, debug messages are printed each time a resource is
allocated/freed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, we only have DM_FLAG_ACTIVATED to indicate the device
status, but we still cannot know in which stage is in progress,
binding or probing.
This commit introduces a new flag, DM_FLAG_BOUND, which is set when
the device is really bound, and cleared when it is unbound.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'ranges' property can be used to specify a translation from the system
address to the bus address. Add support for this using the dev_get_addr()
function, which devices should use to find their address.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present struct eth_device is passed around all over the place. This does
not exist with driver model. Add explicit arguments instead, so that with
driver model we can pass the correct things.
Signed-off-by: Simon Glass <sjg@chromium.org>
The AX_ prefix comes from the Asix driver. Since this is not that, we should
avoid this confusing prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put all global data in a structure and move (what will be) common code into
common functions. This will make the driver-model conversion much easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all boards use garbage collection in their link step, so we should avoid
adding options that rely on this for prevention of code bloat. Add separate
Kconfig options for syscon and regmap uclasses.
Signed-off-by: Simon Glass <sjg@chromium.org>
fdt_addr_t is a physical address. It can be either 64-bit or 32-bit,
depending on the architecture. It should be phys_addr_t instead of
u64 or u32. Similarly, fdt_size_t is changed to phys_size_t.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
fdt_addr_t is changed to phys_addr_t. The format in debug should be updated
to %pa to match the type.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the old drivers (both the normal one and the cros_ec one) now that
we have new drivers that use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that most exynos5250 boards can use the generic exynos5 code, switch
over to it and remove the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that exynos5420 boards can use the generic exynos5 code, switch over to
it and remove the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Hans de Goede
Piotr Zierhoffer
Karol Gugala
Aleksei Mamlin
Tom Rini
Stephen Warren
Alexandre Courbot
Simon Glass
Masahiro Yamada
York Sun