This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds clock definitions and commands to support Keystone2
K2E SOC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convenient to hold configurations for DDR3 PHY and EMIF in
separate common place. This patch moves K2HK DDR3 PHY and EMIF
configuration data with different rates and memory size to a common
ddr3_cfg.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds a common config header file for all the Keystone II
EVM platforms. It combines a lot of general definitions in one file.
The common header included in the EVM should be specific configuration
header.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch moves K2HK board directory to a common Keystone II board
directory. The Board related common functions are moved to a common
keystone board file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With latest v3.13 kernel, unitrd dt fixup is not needed. However for
older kernel versions such as v3.8/v3.10, it is needed. So to work
with both, add a u-boot env variable that can be set to do dt fixup
for older kernels.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This driver is needed in case if keystone driver is used.
Currently only keystone_net driver uses it. So to avoid
redundant code compilation make the keystone_nav dependent
on keystone net driver. It also leads to compilation errors
for boards that does't use it.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use common keystone2 Power Sleep controller base address instead of
directly deciding which keystone2 SoC is used in psc module.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
These functions have been merged into the common GPMC init code
with this commit a0a37183 (ARM: omap: merge GPMC initialization code
for all platform). The file is not compiled any more. So remove it
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Commit a0a37183 (ARM: omap: merge GPMC initialization code for all
platform) broke NAND on OMAP3 based platforms. I noticed this while
testing the latest 2014.07-rc version on the TAO3530 board. NAND
detection did not work with this error message:
NAND: nand: error: Unable to find NAND settings in GPMC Configuration - quitting
As OMAP3 configs don't set CONFIG_NAND but CONFIG_NAND_CMD. the GPMC
was not initialized for NAND at all. This patch now fixes this issue.
Tested on TAO3530 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Pekon Gupta <pekon@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Add support for NAND gpheader image. TI Keystone2 ROM bootloader
expects 8 bytes of trailing zeroes in the nand u-boot image.
So add zeros at the end of the nand gph image.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.
The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.
The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.
Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
As this is a weak function that we may override, provide a prototype for
it.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
To move the arch common function away from board folder to
arch/arm/cpu/armv7/socfpga folder. Its to avoid code duplication
for other non Altera dev kit which is using socfpga device.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Turn on generic board for the integrators, as per the request in
the startup message. Everything just works, tested on the
Integrator/AP and Integrator/CP.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Fix following compilation error when CONFIG_ARM64 is defined
Error: unknown or missing system register name at operand 2
-- `mrs x0,daifmsr daifset,#3'
Signed-off-by: Shaibal.Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Darwin Rambo <drambo@broadcom.com>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
To add the DesignWare watchdog driver support. It required
information such as register base address and clock info from
configuration header file within include/configs folder.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
In current gpio_set_value() implementation, it always sets the gpio control bit
no matter the value argument is 0 or 1. Thus the GPIOs never set to low.
This patch fixes this bug.
The address bus is used as a mask on read/write operations, so that independent
software drivers can set their GPIO bits without affecting any other pins in a
single write operation. Thus we don't need a read-modify-write to update the
register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.
cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Make MMU function reusable. Platform code can setup its own MMU tables.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
This is needed for accessing peripherals with 64-bit MMIO registers,
from ARMv8 processors.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
Hao Zhang
Khoronzhuk, Ivan
Murali Karicheri
Stefan Roese
Andreas Bießmann
Tom Rini
Mugunthan V N
Chin Liang See
Linus Walleij
Stephen Warren
Christian Riesch
Shaibal.Dutta
Łukasz Dałek
Jeroen Hofstee
Albert ARIBAUD
Sergey Kostanbaev
Axel Lin
York Sun
J. German Rivera
Darwin Rambo