The commit 04a9e1180a
cause the 83xx immap broken, so the DMA and PCI will
be failed.
The patch fix the struct spi8xxx and rm struct spi83xx.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hi,
The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
enables the RTS signal with CONFIG_SERIAL_RTS_ACTIVE.
No handshaking is done, but the active RTS signal allows to
connect to the target using a PC which is using RTS/CTS
handshake, and does no harm if the PC is set to ignore RTS.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
allow to load the microde from flash or ram by download it through
the serial or other.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stefan Roese <sr@denx.de>
Hi,
the following patch adds support to move the IXP42X NPE firmware to a
separate flash block, whose start address is defined in
CONFIG_IXP4XX_NPE_EXT_UCODE_BASE. Using that, it is possible to build
NPE-enabled u-boot without copyright problems due to the NPE firmware.
I hope the patch applies, I get whitespace-related differences in the NPE
files due to trailing whitespace in the original versions.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Definition update and change from 16bit to 32bit
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>
- Fix EEPROM_data structure definition according to System EEPROM Data Format.
- Read MAC addresses from EEPROM to ethXaddr before saving ethXaddr to
bd->bi_ethaddr.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch implements the fsl_spi driver on the MPC8349EMDS evaluation board.
This board has an ST M25P40 4Mbit EEPROM on its SPI bus
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family. Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The commit 9e89647889
will cause the mpc8315erdb board can't boot up.
The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk
Dave Liu
Shinya Kuribayashi
Haavard Skinnemoen
Michael Schwingen
Jean-Christophe PLAGNIOL-VILLARD
Andy Fleming
TsiChungLiew
Kim Phillips
Haiying Wang
Timur Tabi
Ben Warren
Stefan Roese