ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
all sh boards use the same cpu linker script so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
currently we need to sync the linker script enty and TEXT_BASE manualy
and the reloc_dst is based on it
instead provide it now from the ldflags
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes a build problem noticed on Apollon by using
mtd_dev_by_eb() instead of "/" as done in the Linux UBI version.
So this brings the U-Boot UBI version more in sync with the Linux
version again.
Signed-off-by: Stefan Roese <sr@denx.de>
new chips supported:-
MX25L1605D, MX25L3205D, MX25L6405D, MX25L12855E
out of which MX25L6405D and MX25L12855E tested on Kirkwood platforms
Modified the Macronix flash support to use 2 bytes of device id instead of 1
This was required to support MX25L12855E
Signed-off-by: Piyush Shah <spiyush@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Looks like when I was encoding the sector sizes, I forgot to divide by 8
(due to the stupid marketing driven process that declares all sizes in
useless megabits and not megabytes).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Due to change in the usb_board_init() prototype, the USB for
the TrizepsIV was not correctly initialized.
Removed dummy print from usb_board_stop().
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch looks okay on u-boot-net.git/next branch
but when it was merged to u-boot.git/master the last line is missing
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.
Without this patch, EMIF configurations made in board_init()
will be invalidated.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Stelian Pop <stelian@popies.net>
sys_eeprom.c: In function 'do_mac':
sys_eeprom.c:323: warning: dereferencing type-punned pointer will break strict-aliasing rules
sys_eeprom.c: In function 'mac_read_from_eeprom':
sys_eeprom.c:395: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Defining the next two configs allows to switch the serial port from the
console using the setenv stdin and stdout
1. #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */
2. #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Nobuhiro Iwamatsu
Nobuhiro Iwamatsu
Jean-Christophe PLAGNIOL-VILLARD
Wolfgang Denk
Stefan Roese
Prafulla Wadaskar
Mike Frysinger
Magnus Lilja
Alessandro Rubini
Stefano Babic
Daniel Gorsulowski
Simon Kagstrom
Kim, Heung Jun
Thomas Lange
Matthias Ludwig
Sedji Gaouaou
Kumar Gala
Peter Tyser
Poonam Aggrwal