This patch added USB PCI-OHCI chips support, interrupt pipe support
and usb event poll support. For supporting the USB interrupt pipe, the
globe urb_priv is moved to purb in ed struct. Now, we can process
several urbs at one time. The interrupt pipe support codes are ported
from Linux kernel 2.4.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
This patch adds USB event poll support, which could be used in usbkbd
and other usb devices driver when the asynchronous interrupt
processing is supported.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com
Using some (very) slow USB keys cause the USB host controller buffers
are not ready to be read by the CPU so we need an extra delay before
reading the USB storage data.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Enable redundant environment, add a MTD partition for it; also add env.
variable command for passing MTD partitions to the kernel command line.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Allow passing longer command line to the kernel - useful especially
for passing MTD partition layout.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Change EEPROM configuration according to the datasheet: "The 24C01A and 24C02A
have a page write capability of two bytes", and "This device offers fast (1ms)
byte write". Add 3ms of extra delay.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
After being reset in mpc5xxx_fec_init_phy(), PHY goes into FX mode, in which
networking does not function. This commit switches PHY to TX mode by clearing
the FX_SEL bit of Mode Control Register. It also reverses commit
008861a2f3, i.e., a temporary workaround.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Both CFG_PCISPEED_66 and CFG_IPBSPEED_133 are misnamed, as defining
them does not cause PCI or IPB clocks to run at the specified speed.
Instead, they configure divisors used to calculate said clocks. This
patch renames the defines according to their real function.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
As pointed out by Bruce Adler <bruce.adler@acm.org> this patch
fixes a small bug in the 405EZ OCM initialization. Thanks for
spotting.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.
Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for 405 PPC's to the 4xx NAND driver
ndfc.c. This is in preparation for the new AMCC 405EZ.
Signed-off-by: Stefan Roese <sr@denx.de>
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
current PHY initalization code (tftp timeouts all the time). This commit
temporarily disables PHY initalization sequence to make the networking
operational, until a fix is found.
Markus Klotzbuecher
Rodolfo Giometti
Zhang Wei
Wolfgang Denk
Bartlomiej Sieka
Stefan Roese
Stefano Babic
Jeffrey Mann
Piotr Kruszynski
Michal Simek