The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
enum board_slots contained six values, where SLOT1 == 1, SLOT2 == 2, and
so on. This is pointless, so remove it. Also move the lane_to_slot[]
array to the top of the file so that it can be used by other functions.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have a dedicated function for setting the node status now, so use it.
Also improve a comment and fix the type of the phandle variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order to figure out which SerDes lane a given Fman port is connected
to, we need a function that maps the fm_port namespace to the srds_prtcl
namespace.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Function fm_info_get_phy_address() returns the PHY address for a given
Fman port. This is handy when the MDIO code needs to fixup the Ethernet
nodes in the device tree to point to PHY nodes for a specific PHY address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using the raw value of 0x80000000 directly in the code can
lead to "count the zeros" bugs like that fixed in commit
718e9d13b98 ("MPC85xxCDS: Fix missing LCRR_DBYP bits for
66-133MHz LBC")
Change all existing raw values to use the symbolic value of
LCRR_DBYP instead.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This change reduces the SPL size by removing the redundant syncs produced
by out_be32 and just replies on one final sync
Done with:
sed -r '/in_be32/b; s/(out_be32)\(([^,]*),\s+(.*)\)/__raw_writel(\3, \2)/g' -i `git grep --name-only sdram_init nand_spl/`
Signed-off-by: Matthew McClintock <msm@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have a requirement to wait a period of time before enabling the
DDR controller
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Let's use the more appropriate udelay for the nand_spl. While we
can't make use of u-boot's full udelay we can atl east use a for
loop that won't get optimized away .Since we have the bus clock
we can use the timebase to calculate wall time.
Looked at reusing the u-boot udelay functions but it pulls in a lot
of code and would require quite a bit of work to keep us within the
very small space constrains we currently have
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We were not comparing the SVRs properly previously. This comparison
will properly shift the SVR and mask off the E bit
This fixes the boot output to show the correct DDR bus width:
512 MiB (DDR3, 16-bit, CL=5, ECC off)
instead of
512 MiB (DDR3, 32-bit, CL=5, ECC off)
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There was an extra 0 in front of the value we were using to mask,
remove it to improve the code.
Also fix the value written to ddr_sdram_cfg to set the bus width
properly to 16 bits
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, for NAND boot for the P1010/4RDB we hard code the DDR
configuration. We can still dynamically set the DDR bus width in
the nand spl so the P1010/4RDB boards can boot from the same
u-boot image
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1015 is the same as P1011 and P1016 is the same as P1012 from software
point of view. They have different packages but share SVRs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provides a tool to build boot Image for PBL(Pre boot loader) which is
used on Freescale CoreNet SoCs, PBL can be used to load some instructions
and/or data for pre-initialization. The default output image is u-boot.pbl,
for more details please refer to doc/README.pblimage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.
NOTE: Because the slave can not erase, write master's NOR flash by
PCIE interface, so it can not modify the ENV parameters stored
in master's NOR flash using "saveenv" or other commands.
environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Put the slave's ucode and ENV into it's own memory space.
4. Normally boot from local NOR flash.
5. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the slave module, need to finish these processes:
1. Set the boot location to one PCIE interface by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID of one PCIE for the boot.
4. Set a specific TLB entry in order to fetch ucode and ENV from
master.
5. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
6. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
1. Updated the README.srio-boot-corenet to add descriptions about
boot from PCIE, and change the name to
README.srio-pcie-boot-corenet.
2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
"xxxx_SRIO_PCIE_BOOT", and the image builded with
"xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
from PCIE.
3. Updated other macros and documents if needed to add information
about boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the powerpc processors with PCIE interface, boot location can be
configured from one PCIE interface by RCW. The processor booting from PCIE
can do without flash for u-boot image. The image can be fetched from another
processor's memory space by PCIE link connected between them.
The processor booting from PCIE is slave, the processor booting from normal
flash memory space is master, and it can help slave to boot from master's
memory space.
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the master module, need to finish these processes:
1. Initialize the PCIE port and address space.
2. Set inbound PCIE windows covered slave's u-boot image stored in
master's NOR flash.
3. Set outbound windows in order to configure slave's registers
for the core's releasing.
4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2"
or "PCIE3" using the following command:
setenv bootmaster PCIE1
saveenv
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added descriptions about boot from PCIE in the files README and
doc/README.srio-pcie-boot-corenet, and changed the name of the
doc/README.srio-boot-corenet to doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:
setenv bootmaster SRIO1
saveenv
The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
1. Reduce a build configuration item in boards.cfg file.
No longer need to build a special image for master, just use a
normal target image and set the "bootmaster" variable.
2. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just set the corresponding value to "bootmaster"
based on the using SRIO port.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Update some descriptions due to the implementation changes:
For master:
Get rid of the SRIOBOOT_MASTER build target, and to support
for serving as a SRIO boot master via environment variable.
For slave:
1. When compile the slave image for boot from SRIO, no longer
need to specify which SRIO port it will boot from.
2. All slave's cores should be in hold off.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.
Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:
fsl_cpu_a011:disable
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This is needed to make room for a bugfix on p1_p2_rdb_pc. A sync is used
before the final write to LSOR that initiates the transaction, to ensure
all the other set up has been completed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The code first aligns the SP to 16 then subtract 8, making it
8 bytes aligned. Furthermore the initial stack frame not
quite correct either.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PowerPC mandates SP to be 16 bytes aligned.
Furthermore, a stack frame is added, pointing to the reset vector
which may in the way when gdb is walking the stack because
the reset vector may not accessible depending on emulator settings.
Also use a temp register so gdb doesn't pick up intermediate values.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 8b5a02640a ("Makefile: cosmetic:
optimize usage of LIBS-y") broke the build of boards that have a board
vendor "common" directory, by introducing a space between "LIBS-" and
"y".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
commit 54652991
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips
fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads
to problems for smaller versions of this chip e.g. the 32Mbit version
with deviceid 0x16 on mgcoge. So move the code for this work around to
an own function and check previously manufacturer id and device id to
not break other flashes which don't need this work around.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Philippe De Muyter <phdm@macqel.be>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Erasing flash sectors protected with persistent protection bit (PPB)
mechanism on Spansion flash chips doesn't work. Add sector protection
status checking and sector lock and unlock commands to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add '-ansi' to DTS_CPPFLAGS to avoid unwanted expansion of dts content
that matches some predefined macros.
Example: A number of PowerPC related *.dts files in the kernel define a
property named 'linux,network-index' which (w/o '-ansi') is expanded to
'1,network-index' by the preprocessor because of '#define linux 1.'
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
Support for DS1388 is added by extending the DS1337 driver. DS1388 is
similar to DS1337. The time registers are offset by 1 (due to support
for hundreds of seconds), and there is no century bit.
The configuration and trickle charge registers are also different.
Tested on hardware with Freescale P2010 and DS1388.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Make sure that $(LDSCRIPT) is not empty before calling process_lds
with 'cat $(LDSCRIPT)' else cat will block waiting for input from
stdin.
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
Synchronize with ALL-y handling and code in spl/Makefile.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The top Makefile and the SPL Makefile have lines like those:
ifneq ($(CONFIG_AM33XX)$(CONFIG_OMAP34XX)$(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),)
LIBS += $(CPUDIR)/omap-common/libomap-common.o
endif
ifeq ($(SOC),mx5)
LIBS += $(CPUDIR)/imx-common/libimx-common.o
endif
This should be done in the arch/CPU/SoC specific sub-makefiles to
keep the top Makefiles clean. This patch also allows adding of new
arch/CPU/SoC specific libraries in the future without touching
the top Makefiles.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Fixes the build-time warning:
board.c: At top level:
board.c:106: warning: 'pmu_init' defined but not used
This makes the ifdef logic at the call site match the logic at the
function definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fixes the build-time warning:
board.c: In function 'board_init_r':
board.c:304: warning: unused variable 's'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Nothing is using this, so punt it from the gd. Seems to just be a copy
& paste wart from the initial port.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
U-Boot port is based on sources forked from GRUB-0.97 by Sun in 2004,
which can be found here:
http://src.opensolaris.org/source/xref/onnv/onnv-gate/usr/src/grub/grub-0.97/stage2/zfs-include/zfs.h
Released by Sun for GRUB under the license:
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
GRUB official releases include ZFS in version:
ftp://alpha.gnu.org/gnu/grub/grub-1.99~rc1.tar.gz
And patched against GRUB Bazaar repository for ashift fixes (4KB HDDs)
more conveniently found at github:
e7b6ef3ac3
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
This patch updates the yaffs2 in u-boot to correspond to
git://www.aleph1.co.uk/yaffs2
commit id 9ee5d0643e559568dbe62215f76e0a7bd5a63d93
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
When reset code is in flash, the jump instructions emitted by the
compiler are relative instead of absolute jumps.
A fix to the reset code to make correct jumps to the beginning of
code relocated to RAM have also been added.
Signed-off-by: Julius Baxter <juliusbaxter@gmail.com>
When CONFIG_ZERO_BOOTDELAY_CHECK is not defined, bootdelay==0
prevents the check for console input (as stated in README.autoboot).
This must also work in CONFIG_AUTOBOOT_KEYED mode.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Add support for specifying a differnt CPU for main u-boot and SPL
u-boot builds. This is done by adding an optional SPL CPU after the
main CPU in boards.cfg as follows:
normal_cpu:spl_cpu
This this case CPU will be set to "normal_cpu" during the main u-boot
build and "spl_cpu" during the SPL build.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.
Chage protoype declaration as static.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32
Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
In addition to the error message also display the error code. I had the
problem that my malloc memory was not enough (ENOMEM), and if u-boot
had displayed the error code immediately that would have saved me some
debugging.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Use ubifs_err instead of printf.
Add "errno=%d" in output as suggested by Albert Aribaud.
Signed-off-by: Thomas Weber <weber@corscience.de>
Since run_command() and run_command_list() are important and a little
confusing, add some basic tests to check that the behaviour is correct.
Note: I am not sure that this should be committed, nor where it should go
in the source tree. Comments welcome.
To run the unit tests use the ut_cmd command available in sandbox:
make sandbox_config
make
./u-boot -c ut_cmd
(To test both hush and built-in parsers, you need to manually change
CONFIG_SYS_HUSH_PARSER in include/configs/sandbox.h and build/run again)
Signed-off-by: Simon Glass <sjg@chromium.org>
Any environment variable can hold commands to be executed by the 'run'
command. The environment variables preboot, bootcmd and menucmd have
special code for triggering execution in certain circumstances.
We adjust these calls to use run_command_list() instead of run_command().
This change permits these variables to have embedded newlines so that
they work the same as the 'source' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Timur Tabi
Paul Gortmaker
Matthew McClintock
York Sun
Shaohui Xie
Liu Gang
Scott Wood
Joakim Tjernlund
Holger Brunck
Anatolij Gustschin
Horst Kronstorfer
Kenth Eriksson
Daniel Schwierzeck
Mike Frysinger
Jorgen Lundman
Charles Manning
Julius Baxter
Jens Scharsig
Dirk Eibach
Allen Martin
Fabio Estevam
Timo Ketola
Prabhakar Kushwaha
Bernhard Walle
Simon Glass