Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.
We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
All objects under post/ directory are enabled by CONFIG_HAS_POST.
(post/tests.o is enabled by CONFIG_POST_STD_LIST.
But CONFIG_POST_STD_LIST depends on CONFIG_HAS_POST.)
We can move CONFIG_HAS_POST switch to the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
$(LDSCRIPT) is a source file, not a generated file.
We do not need a make rule of $(LDSCRIPT).
And one more trivial fix:
$(obj)/u-boot should not dierectly depend on $(LDSCRIPTS).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If U-Boot build with DEBUG enabled/defined the first call of "debug"
function (that dumps data to any available console) will happen before
zeroing of initial "gd" in init call "zero_global_data" in
"init_sequence_f".
And if stack was not filled with zeros chances are high that
"gd->have_console" won't be 0. In its turn it will cause attempt to
output things to non-initialized yet serial console.
So for safety and predictability we set "gd->have_console = 0".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
argv[0] contains bootvx (command name) not the load address, if called with
argv < 2 use load_addr, else use address argument given to the command.
Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com>
Before this commit, output files under tpl/ directry
were not ignored.
This commit fixes this problem.
And we have only one source file under spl/ directory:
spl/Makefile
So, we can describe .gitignore more simply.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
PLATFORM_RELFLAGS += -meabi
PLATFORM_CPPFLAGS += -ffixed-r2
were defined in all arch/powerpc/${CPU}/config.mk.
This commit moves them to arch/powerpc/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The documentation suggested the arguments where passed over r3-r6
while the code below simply does that over r0-r3.
Cc: Kumar Gala <galak@kernel.crashing.org>
Commit 8dfafdde88 ("Introduce common timer functions") created a
common definition of usec_to_tick() which had a couple problems:
static unsigned long long usec_to_tick(unsigned long usec)
{
uint64_t tick = usec * get_tbclk();
That likely overflows.
usec *= get_tbclk();
That was an attempt to fix it by performing the multiply after the
promotion of usec to 64-bit, but was applied to the wrong variable,
which was never used.
This patch fixes these issues. A user-visible symptom of the problem was
the e.g. "dhcp zImage" using an ASIX USB Ethernet dongle would print:
Waiting for Ethernet connection... unable to connect.
... with no delay before "unable to connect". There are likely other
symptoms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Some editors such as Emacs can highlight source files.
But their parser algorithm is not perfect.
If you use one double-quotation alone, some editor cannot
handle it nicely and mark source lines as a string by mistake.
It is preferable to use two double-quotations as a pair.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The build rules of
- include/autoconf.mk.dep
- include/autoconf.mk
- include/spl-autoconf.mk
- include/tpl-autoconf.mk
were not nice.
They created empty files (which are never updated)
if an error occurs during preprocessing.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Given a multi-file image created through the mkimage's -d option:
$ mkimage -A x86 -O linux -T multi -n x86 -d vmlinuz:initrd.img:System.map \
multi.img
Image Name: x86
Created: Thu Jul 25 10:29:13 2013
Image Type: Intel x86 Linux Multi-File Image (gzip compressed)
Data Size: 13722956 Bytes = 13401.32 kB = 13.09 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 4040128 Bytes = 3945.44 kB = 3.85 MB
Image 1: 7991719 Bytes = 7804.41 kB = 7.62 MB
Image 2: 1691092 Bytes = 1651.46 kB = 1.61 MB
It is possible to perform the innverse operation -- extracting any file from
the image -- by using the dumpimage's -i option:
$ dumpimage -i multi.img -p 2 System.map
Although it's feasible to retrieve "data files" from image through scripting,
the requirement to embed tools such 'dd', 'awk' and 'sed' for this sole purpose
is cumbersome and unreliable -- once you must keep track of file sizes inside
the image. Furthermore, extracting data files using "dumpimage" tool is faster
than through scripting.
Signed-off-by: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to avoid duplicating code and keep only one point of modification,
the functions, structs and defines useful for "dumpimage" were moved from
"mkimage" to a common module called "imagetool".
This modification also weakens the coupling between image types (FIT, IMX, MXS,
and so on) and image tools (mkimage and dumpimage). Any tool may initialize the
"imagetool" through register_image_tool() function, while the image types
register themselves within an image tool using the register_image_type()
function:
+---------------+
+------| fit_image |
+--------------+ +-----------+ | +---------------+
| mkimage |--------> | | <-----+
+--------------+ | | +---------------+
| imagetool | <------------| imximage |
+--------------+ | | +---------------+
| dumpimage |--------> | | <-----+
+--------------+ +-----------+ | +---------------+
+------| default_image |
+---------------+
register_image_tool() register_image_type()
Also, the struct "mkimage_params" was renamed to "image_tool_params" to make
clear its general purpose.
Signed-off-by: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function should be declared static.
Signed-off-by: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
care about this parameter or it should be gone completely.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
For LPC32XX high-speed UART it is required to send a carriage return
symbol along with line feed. The problem was introduced in e503f90a
commit.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MHz. Fixing the same and cleaning the
previously used dpll values.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Commit "armv7: hw_data: change clock divider setting"
updates the setting for m6 divider for 20MHz sys_clk frequency.
But missed to update for other sys_clk frequencies. Doing the same.
Reported-by: Rajendran, Vinothkumar <vinothr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
"ULPI: ulpi_reset: failed writing reset bit"
So, remove it.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
commit 16297cfb2a
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Fri Oct 4 19:22:26 2013 +0200
usb: new board-specific USB init interface
introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
ABB code uses LDELAY but does not include the header that provides its
definition.
Include the header.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nishanth Menon <nm@ti.com>
To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: Tom Rini <trini@ti.com>
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html
Tested on OMAP4460 PANDA.
Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Test on Beaglebone white over cpsw, usb ether and SD card (read and
write), performance increased, crc32 of data matches.
Signed-off-by: Tom Rini <trini@ti.com>
The standalone programs do not use the api calls, but rely
directly on u-boot variable gd->jt for the jump table. Commit
fe1378a - "ARM: use r9 for gd" changed the register holding
the address of gd, but the assembly code in the standalone
examples was not updated accordingly. This broke the programs
on ARM relying on the jumptable in the v2013.10 release.
This patch unbricks them by using the correct register.
Cc: Michal Simek <monstr@monstr.eu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Revert commit 0f5141e9 which causes boards starting in
FLASH to try and write to a FLASH location.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The default value of CONFIG_SYS_FSL_TBCLK_DIV is 16.
So, update its value as default.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers with
__iomem pointers for tsec.
p1_p2_rdb_pc.c:373:24: warning: incorrect type in assignment (different
address spaces)
p1_p2_rdb_pc.c:373:24: expected struct tsec_mii_mng [noderef]
<asn:2>*regs
p1_p2_rdb_pc.c:373:24: got struct tsec_mii_mng *<noident>
Use TSEC_GET_MDIO_REGS_BASE() for the remaining mdio 'regs'
initializations to remove the __iomem warnings and for consistency.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
As mEMAC1 and mEMAC2 are dual-role MACs, which are used as 1G or 10G MAC.
So we update dynamically 'cell-index' to '2' and '3' for 10GEC3 and 10GEC4.
Also change 'fsl,fman-port-1g-rx' to 'fsl,fman-port-10g-rx', ditto for Tx.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
A new valid setting case added for fman1, it uses platform frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Masahiro Yamada
Alexey Brodkin
Stany MARCEL
Kees Jongenburger
Tom Rini
Stephen Warren
Guilherme Maciel Ferreira
Vladimir Zapolskiy
Lokesh Vutla
Nikita Kiryanov
Yegor Yefremov
Heiko Schocher
Dan Murphy
Stefan Roese
Tapani Utriainen
Jeroen Hofstee
Albert ARIBAUD
Prabhakar Kushwaha
Claudiu Manoil
Shengzhou Liu
Shaohui Xie