Commit 98e6956 "mpc52xx: add support for tqm52xx based board charon"
caused build warnings on some systems. Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Commit 722b061 "autocomplete: remove runtime handler install" caused
some boards (like NETTA2_V2) to break with errors like these:
cmd_net.c:296: error: expected expression before ',' token
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Convert the variable omap3_evm_version to u32 to work around
some broken linkers from older tool chains. E.g. CodeSourcery's
2009q1-203 ld 2.19.51.20090205. Without this, these linkers
stop linking 'omap3_evm' or at least issue a warning. Like
arm-none-linux-gnueabi-ld: section .bss [8003f5e0 -> 8007e337] overlaps section .rel.dyn [8003f5e0 -> 80044e57]
arm-none-linux-gnueabi-ld: section .dynsym [80044e58 -> 80044ef7] overlaps section.bss [8003f5e0 -> 8007e337]
arm-none-linux-gnueabi-ld: u-boot: section .bss vma 0x8003f5e0 overlaps previous sections
CC: Sanjeev Premi <premi@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
The current code use all the voltage range support by the host
controller to do the validation. This will cause problem when
the host supports Low Voltage Range. Change the validation
voltage to be based on board setup.
Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The max clock of MMC is 52MHz
Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.
Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add reginfo as a default command for p1022ds boards
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current code use all the voltage range support by the host
controller to do the validation. This will cause problem when
the host supports Low Voltage Range. Change the validation
voltage to be based on board setup.
Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The max clock of MMC is 52MHz
Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.
Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Yaffs image require to use the oob to store some info, so when we
burn the yaffs image, we need to also write the image's oob part
into flash.
This patch add addition suffix to onenand write to give the uboot
the power to directly burn the yaffs image to onenand.
Signed-off-by: Lei Wen <leiwen@marvell.com>
This is part of the timer cleanup effort.
In the future we only use get_timer() in its intended way to
program timeout loops.
reset_timer() shall not be used anymore.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Fix clock divider for COM57H5M10XRC display.
The previous setting caused flicker.
Tested on Qong (EVBLite with COM57H5M10XRC).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Multiple rules are using the expanded AFLAGS/CFLAGS settings and some are
getting so long that the rules need to be line wrapped. So unify them in
one variable, use that variable in the rule, and then unwrap things. This
makes the actual `make` output nicer as it doesn't have line continuations
in it anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In some usages of inline assembly, hard-coded registers were
specified when a scratch register should have been used instead.
Signed-off-by: Timur Tabi <timur@freescale.com>
The non-reentrant versions of the hashtable functions operate on a single
shared hashtable. So if two different people try using these funcs for
two different purposes, they'll cause problems for the other.
Avoid this by converting all existing hashtable consumers over to the
reentrant versions and then punting the non-reentrant ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The following commit:
commit 882b7d726f
Author: Mike Frysinger <vapier@gentoo.org>
Date: Wed Oct 20 03:41:17 2010 -0400
do_reset: unify duplicate prototypes
missed the 74xx_7xx and mpc86xx arches and the ppmc7xx board do_reset()
functions which resulted in build errors such as:
cpu.c:128: error: conflicting types for 'do_reset'
include/command.h:102: error: previous declaration of 'do_reset' was here
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
By rearranging the linker script we get support for
relocation of -fpic for free.
Move __got2_entries outside _GOT2_TABLE_ defining scope
matching the rest of PowerPC
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
By rearranging the linker script we get support for
relocation of -fpic for free.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
PT7C4338 chip is being manufactured by Pericom Technology Inc.
It is a serial real-time clock which provides:
1)Low-power clock/calendar.
2)Programmable square-wave output.
It has 56 bytes of nonvolatile RAM.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
While we're here, cut out the useless id defines too.
Signed-off-by: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds the possibility to (optinally) write to the
flash configuration register. The Intel style CFI chips support
such a register that can be used to configure the operation
mode to a non-default value.
This method will be used by the t3corp board, which needs to
configure the DS617 Xilinx flash for async read mode.
Signed-off-by: Stefan Roese <sr@denx.de>
The function sector_erased() is modified to not use pointer
access, but to use the correct accessor functions. This fixes a
problem on the t3corp board with the Xilinx DS617 flash chips. Here
a board specific accessor function is needed to read from flash
in 32bit mode. This patch enables such an operation mode.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds some calls to set the flash chip in the read-status-
register- or read-id-mode before the corresponding register is
read back. This problem was detected while porting the common CFI
driver to support the Xilinx DS617 flash chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the PPC4xx ethernet POST loop test count from
currently 192 (256 - 64) to a default of 10. While doing this the max
frame size is increased. Each loop run uses a different frame size,
starting with a max of 1514 bytes, down to 64. The default loop
count of 10 can be overriden using CONFIG_SYS_POST_ETH_LOOPS in the
board config header.
The TEST_NUM loop has been removed as it was never used.
The main reason for this change is to reduce the boot time on boards
using this POST test, like the lwmon5 board. This change reduces the
boot time by about 600ms on the lwmon5 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
This patch includes the following changes for the lwmon5 board support:
- Enable cache in SDRAM
- Use common EHCI driver instead of the PPC4xx specific OHCI driver
This can be done since only high-speed devices are connected.
- Remove cached TLB entry again after ECC setup
- Use correct define for cache enabling
(CONFIG_4xx_DCACHE instead of CONFIG_SYS_ENABLE_SDRAM_CACHE)
- Enable FIT image support
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk
Mike Frysinger
John Rigby
Dirk Behme
Li Yang
Jerry Huang
Jerry Huang
Matthew McClintock
Florian Fainelli
Lei Wen
Reinhard Meyer
Stefano Babic
Timur Tabi
Peter Tyser
Joakim Tjernlund
Priyanka Jain
Heiko Schocher
Wojtek Skulski
Chong Huang
Sandeep Paulraj
Stefan Roese
Ricardo Ribalda Delgado