Add DM support to the SH QSPI driver while retaining non-DM support.
The later is required as this driver is used in SPL which has a size
limitation of 16 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
[jagan: use proper commit head]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Convert fsl_qspi.c to complete DM mode.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Tested-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Tested-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add code to reset all reset signals as in SPI DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Release reset when _remove().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This adds support for the ARM PL022 SPI controller for the standard
variant (0x00041022) which has a 16bit wide and 8 locations deep TX/RX
FIFO.
A few parts were borrowed from the Linux kernel driver.
Cc: Armando Visconti <armando.visconti@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.
This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Add spi driver for sun4i, sun5i and sun7i SoCs. The driver is
adapted from mailine kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This matches the compatible string used by the Linux kernel. This will
allow u-boot to use the same device tree files.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: use armada instead of orion on .data]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Get the is_errata_50mhz_ac in .ofdata_to_platdata, and
reuse it in .set_mode this can eventually initialized
dt code at once and adding room to add platdata.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
[jagan: removed GQSPI_MIO_NUM_ macros]
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch is for the startup block issue in the spi controller.
SPI clock is passing through STARTUP block to FLASH. STARTUP block
don't provide clock as soon as QSPI provides command. So, first
command fails.
This patch added support to read JEDEC id in xilinx_spi_xfer ().
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch modify xilinx_spi_xfer() function and add rxfifo() and
txfifo() functions to add the modularity so that these functions
can be used by other functions within the same file.
This patch also added support to read fifo_size from dts.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch added support to read register base address from DTS file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Use "%p" to print cmdbuf.
Compilation warning as below:
CC spl/drivers/spi/cadence_qspi_apb.o
LD spl/lib/built-in.o
drivers/spi/cadence_qspi_apb.c: In function ‘cadence_qspi_apb_indirect_write_setup’:
drivers/spi/cadence_qspi_apb.c:696:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
cmdlen, (unsigned int)cmdbuf);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Use "%zu" for size_t data type.
Compilation warning as below:
In file included from include/linux/bug.h:7:0,
from include/common.h:26,
from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
The claim/release bus function must not reset the whole SPI core because
settings regarding wordlen, clock-frequency and so on made by
set_wordlen, set_mode, set_speed get lost with this action. Resulting in
a non-functional SPI.
Without DM the failure didn't came up since after the spi_reset within
claim bus all the setup (wordlen, mode, ...) was called, in DM they are
called by the spi uclass.
We change now the things as following for having a working SPI instance
in DM:
- move the spi_reset(...) to the probe call in DM for having a known
hardware state after probe. Without DM we don't have a probe call, so we
issue the reset as before during the claim_bus call.
- in release bus we just reset the modulctrl to the reset-value (spi-
slave)
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
commit 8480792287
("spi: omap3: Skip set_mode, set_speed from claim") did break SPI
support on my AM335x board.
The named commit:
- ignored the responsible arguments (speed, mode)
The set speed/mode function must use the supplied function arguments to
work properly. With this commit we take those arguments and transfer
them to the priv-data.
- used wrong udevice pointer for getting priv data
the udevice-pointer within function argument is already the spi-bus
device, so it is wrong looking here for some parent (ocp-bus in this
case) and getting priv-pointer from there.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Otherwise the frequency is zero and the clock divider cannot be setup by
'omap3_spi_set_speed' function.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CS GPIO activation low/high is determinated by the device tree
so we don't need to take in accoung in cs_activate and cs_deactivate
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch replaced "return 0" with "return status" to fix the
incorrect return value error reported by the coverity.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Change to use devfdt_get_addr_index() function to get fdt address.
Original code has compilation warning below:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_ofdata_to_platdata’:
drivers/spi/cadence_qspi.c:297:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
plat->regbase = (void *)data[0];
^
drivers/spi/cadence_qspi.c:298:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
plat->ahbbase = (void *)data[2];
^
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Fix warning as below when compile in 64-bit.
warning: format '%u' expects argument of type
'unsigned int', but argument 6 has type 'size_t
{aka long unsigned int}
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
In
void *rx_addr = NULL;
rx_add = A;
the first assignment has no effect. Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For SPI_XFER_BEGIN | SPI_XFER_END the code sets data_out = NULL.
In the debug statement we should not dereference this value.
As we do not transfer any data the debug statement is not needed in this
case anyway.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In some situation, QSPI controller is already configured by an early
boot stage, adding reset support will insure that QSPI controller is
started from a pristine state.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Use dev_read_xxx() instead of old manner fdt_xxx() API
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Quad-SPI interface is able to manage 2 spi nor devices.
FSEL bit selects the flash memory to be addressed in single flash mode.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add "st,stm32f469-qspi" compatible which is used on kernel side.
This will be necessary when DT will be synchronised from kernel.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As all platforms which uses this driver have CONFIG_CLK flag
enable in their defconfig, we can remove it from driver code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since now we have driver for clocks on Armada 37xx, use it to determine
SQF clock frequency for the SPI driver.
Also change the default config files for Armada 37xx devices so that
the clock driver is enabled by default, otherwise the SPI driver cannot
be enabled.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Some SoCs have different endianness of QSPI IP if compared
to endianness of core. The function is_controller_busy()
checks if the QSPI controller is busy or not, considering
the endianness of the QSPI IP.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
While switching to readl_poll_timeout macros from custom code
the waiting condition was accidently inverted, so it was pure
luck that this code works at least in some conditions.
Fix that by inverting exit condition for readl_poll_timeout.
Fixes: c6b4f031d9 ("DW SPI: fix tx data loss on FIFO flush")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The QSPI controller on RCar Gen2 has 32byte FIFO. Instead of doing
the SPI transmission 1 byte at time, if there is a 32byte chunk of
data to be transferred, fill the FIFO completely and then transfer
the data to/from the FIFO. This increases the SPI NOR access speed
significantly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Replace the ad-hoc endless loops with wait_for_bit() with
reasonable timeout. Note that the loops had internal 10uS
delays, although there is no reason for those on this HW,
so they are dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Waiting for SPBDCR == 1 is not required and is covered by the
subsequent wait for SPSR_SPRFF, so drop this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Just replace unsigned {char,short,long} with u{8,16,32},
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Add driver for the RPC block in SPI-flash mode. This driver allows
access to a SPI NOR flash attached to the RPC block and does not
support RPC in Hyperflash mode. Note that this block is extremely
selective when communicating with the SPI NOR.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut
Ashish Kumar
Ley Foon Tan
Quentin Schulz
Boris Brezillon
Stefan Mavrodiev
Chris Packham
Jagan Teki
Christophe Kerello
Siva Durga Prasad Paladugu
Vipul Kumar
Michal Simek
Thomas Fitzsimmons
Hannes Schmelzer
Michael Trimarchi
Álvaro Fernández Rojas
Rick Chen
Heinrich Schuchardt
Patrice Chotard
Patrick Delaunay
Marek Behún
Rajat Srivastava
Tom Rini
Adam Ford
Eugeniy Paltsev
Marek Vasut