This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.
This patch supports the following functions:
- 256MB DDR3-SDRAM
- SPI ROM
- Ethernet
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch add the MX53 boot image support.
This patch has been tested on Freescale MX53EVK board
and MX51EVK board.
Signed-off-by: Jason Liu <r64343@freescale.com>
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.
Enable address parity and RCW by default for RDIMMs.
Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.
Use a formula to calculate rodt_on for timing_cfg_5.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.
Updated hwconfig calls to use local buffer.
Syntax is
hwconfig=fsl_ddr:ecc=on
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By default, "-" chars are interpreted as hyphens (U+2010) by groff, not
as minus signs (U+002D). Since options to programs use minus signs
(U+002D), this means for example in UTF-8 locales that you cannot cut
and paste options, nor search for them easily.
(Reported by lintian.)
Signed-off-by: Loc Minier <loic.minier@linaro.org>
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
boards
- change doc/README.cfi as Stefan Roese suggested
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
This config option is for an erratum workaround; rename it to be more
clear. Also, drop it from config files don't need it and were
undefining it.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The barco board appears to be unmaintained since it was added about 5
years ago. The environment location has probably never been correct.
Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marc Leeman <marc.leeman@barco.com>
Acked-by: Stefan Roese <sr@denx.de>
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year. Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
The TI DA850/OMAP-L138/AM18x EVM can be populated with devices
having different maximum allowed CPU clock rating.
The maximum clock the chip can support can only be determined from
the label on the package (not software readable).
Introduce a method to pass the maximum allowed clock rate information
to kernel using ATAG_REVISION. The kernel uses this information to
determine the maximum cpu clock rate reachable using cpufreq.
Note that U-Boot itself does not set the CPU clock rate. The CPU
clock is setup by a primary bootloader ("UBL"). The rate setup by
UBL could be different from the maximum clock rate supported by the
device.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The README.davinci in documentation folder is missing information
regarding DA850 which is a supported DaVinci device.
Add this information.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Add the ability to not report an I2C POST error for a set of given I2C
addresses on bootup. This is useful for cases when a device may or may
not be present, and neither case is considered an error. For example:
- Some form factors such as XMC and Compact PCI Express have an I2C
EEPROM whose address changes based on geographical address. Eg
installed in one slot its EEPROM address is, 0x50, in another its
0x51, etc. This allows multiple devices to have their EEPROMs present
on the same I2C bus. Thus the I2C devices present for an XMC or
CPCIe card depend on if and where other cards are installed in the
same system.
- Some cards have optional I2C devices. Eg one hardware build
configuration has different I2C devices than another and software
can't determine if the optional device should be present or not.
- Some cards have optional daughtercards with I2C devices on them.
- I2C EEPROMs address range depends on their size. Its possible to
support differently size EEPROMs by only probing the EEPROM's base
address and ignoring the other addresses that are impacted by its
size.
A new CONFIG_SYS_POST_I2C_IGNORES define has been added which specifies
a list of I2C addresses for the I2C POST to ignore.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The memory test is performed after DDR initialization when U-boot stills runs
in flash and cache. On recent mpc85xx platforms, the total memory can be more
than 2GB. To cover whole memory, it needs be mapped 2GB at a time using a
sliding TLB window. After the testing, DDR is remapped with up to 2GB memory
from the lowest address as normal.
If memory test fails, DDR DIMM SPD and DDR controller registers are dumped for
further debugging.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a document to maintain a list of boards removed from the current
source tree, so archeologists can check more easily if here is
something they might want to dig for...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 14d0a02a "Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE" missed a
few places, especially for boards that were added inbetween. Fix the
remaining issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
ELF relocation tables generated with linker option -pie can
be used to fixup code and data in a single loop at relocation,
removing the need for manual fixups anywhere else in the code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled. Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.
The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.
Also configure a pin muxing to select some SSI signals, which will disable
I2C1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Change the implementation for arm926 to relocate the code to
an arbitrary address in RAM.
Adapt the TX25 (i.MX25), magnesium board to test the changes.
On the tx25 board TEXT_BASE is set to the final relocation
address to prevent one more copying of u-boot code
when relocating. More info see:
doc/README.arm-relocation
da850 board:
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
!! This breaks support for all arm boards !!
To compile in old style, you must define
CONFIG_SYS_ARM_WITHOUT_RELOC or you can compile
with "CONFIG_SYS_ARM_WITHOUT_RELOC=1 ./MAKEALL board"
!! This define will be removed soon, so convert your
board to use relocation support
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fix boot from NAND for non-ARM systems
Signed-off-by: Wolfgang Denk <wd@denx.de>
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some Linux distributions include the "mkimage" as a package.
This commit provides a manual page for mkimage.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Added documentation for FIT images and examples.
Moved to doc/ directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_IDE_SWAP_IO
This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual
rank with 512MB each rank.
Also check dimm size and rank size for memory controller interleaving
Signed-off-by: York Sun <yorksun@freescale.com>
Replace environmental variables memctl_intlv_ctl and ba_intlv_ctl with
hwconfig parameters. The syntax is
setenv hwconfig "fsl_ddr:ctlr_intlv=<mode>,bank_intlv=<mode>"
The mode values for memory controller interleaving are
cacheline
page
bank
superbank
The mode values for bank interleaving are
cs0_cs1
cs2_cs3
cs0_cs1_and_cs2_cs3
cs0_cs1_cs2_cs3
Signed-off-by: York Sun <yorksun@freescale.com>
Designware network driver support added.
This is a Synopsys ethernet controller
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Simon Glass
Wolfgang Denk
Yoshihiro Shimoda
Mike Rapoport
Stefano Babic
Liu Hui-R64343
York Sun
Loïc Minier
Heiko Schocher
Becky Bruce
Kumar Gala
Sughosh Ganu
Sekhar Nori
Peter Tyser
Ilya Yanok
Stefan Roese
Albert Aribaud
Timur Tabi
Reinhard Meyer
Kim Phillips
Heiko Schocher
Nobuhiro Iwamatsu
Albert Aribaud
Vipin KUMAR
Thomas Chou