The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Thus far, the socfpga init code had hard-coded the configuration
of the ethernet PHY interface to RGMII in the ethernet registers
in sysmgr space, so PHYs connected in another modes did not work.
This patch fixes support for configurations where the ethernet PHYs
are connected over MII/GMII/RMII interfaces by parsing the phy-mode
OF property of the GMACs and configuring the ethernet registers in
sysmgr space accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The following patch caused cpu_eth_init() to not be called anymore
for DM-capable boards:
commit c32a6fd07b
Date: Sun Jan 17 14:51:56 2016 -0700
net: Don't call board/cpu_eth_init() with driver model
This breaks ethernet on SoCFPGA, since we use that function to un-reset
the ethernet blocks. Invoke the ethernet reset function from arch_misc_init()
instead to fix the breakage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Make sure the NAND reset is not asserted in full U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
The L2 cache was never enabled in the v7_outer_cache_enable(), fix
this and enable the L2 cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
This function triggers the registration of the dwmmc driver on SoCFPGA,
but this is not needed in case the driver is correctly probed from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Update the L2 AUX CTRL settings for the SoCFPGA.
Enabling D and I prefetch bits helps improve SDRAM performance on the
platform.
Also, we need to enable bit 22 of the L2. By not having bit 22 set in the
PL310 Auxiliary Control register (shared attribute override enable) has the
side effect of transforming Normal Shared Non-cacheable reads into Cacheable
no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Add code which uses the new functions for obtaining FPGA ID from
the scan manager. This new code prints the FPGA model attached to
the SoCFPGA during boot and sets environment variable "fpgatype",
which can be used to determine the FPGA model in U-Boot scripts.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Add a small workaround into the platform code which forces the SDMMC
into 8-bit mode (the default configuration for all socfpga platforms)
to work around breakage caused by missing patches in mainline which
switch the probing of SD/MMC to OF instead of static configuraiton.
The patches will hit mainline after the SPL series, so to avoid build
issues, add this small temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Reset the GMAC ethernets based on the "resets" OF node instead of ad-hoc
hardcoded values in the U-Boot code. Since we don't have a proper reset
framework in place yet, we have to do this slightly ad-hoc parsing of the
OF tree instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The GMAC can now be probed from OF, so enable DM ethernet and remove the
old ad-hoc designware_initialize() invocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
setenv an environment variable called "bootmode" , which contains the
board boot mode. This can be in turn used in scripts to determine from
where to load kernel and such.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for printing from which device the SoCFPGA board booted.
This decodes the BSEL settings and prints it in human readable form.
Signed-off-by: Marek Vasut <marex@denx.de>
Write necessary magic value into the Warm Boot from ON-Chip RAM
group Enable register to enable Warm reset support. Instead of
doing this in the reset_cpu() function, we do it in arch early
init to avoid breaking old kernel code which expects this magic
value to be already written into this register.
This magic is originally excavated from common/spl/spl.c in the
u-boot port from altera, where this value was written just before
the SPL jumped to actual U-Boot in the RAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Replace all those ad-hoc reset functions, which were all copies
of the same invocation of clrbits_le32() anyway, with one single
unified function, socfpga_per_reset(), with necessary parameters.
Signed-off-by: Marek Vasut <marex@denx.de>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The current current watchdog timeout of 12 seconds is a bit small for
booting into Linux, especially when using a NFS based rootfs. So lets
change this timeout to a more defensive value of 30 seconds.
Also we now call the hw_watchdog_init() function so that we override
the value already configured from the Preloader.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
This function will be needed by the upcoming Designware master SPI
driver. As the SPI master controller is held in reset by the current
Preloader implementation. So we need to release the reset for the
driver to communicate with the controller.
This function is called from arch_early_init_r() if the SPI
driver is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Move this initialization code to proper place. The misc_init_r()
function is called way too late and the platform initialization
code should be executed much earlier.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Pavel Machek <pavel@denx.de>
Add command to enable and disable the bridges between HPS and FPGA.
This patch does have a checkpatch issue with the assembler portion,
checkpatch correctly complains that there should be no whitespace
before quoted newline. I do not agree that fixing this specific
checkpatch issue will improve the readability, thus this one is not
addressed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Move icache_enable() and dcache_enable() function calls from
board code into the CPU code and into the enable_caches()
function. This is how the cache enabling code was designed
to work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add code which configures the AMBA NIC-301 and the SCU on the SoCFPGA .
The code sets the access permissions for the CPU to the AMBA slaves such
that the CPU can access them in both secure and non-secure mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Configure the PL310 address filter to make sure DRAM is mapped to 0x0.
This code also configures the "remap" register of NIC-301 and sets the
required 'mpuzero' bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move the not-CPU specific stuff into drivers/fpga/ and base
this on the cleaned up altera FPGA support.
Cosmetic change to the print_cpuinfo() function output. Align the
output with the rest of initial output produced by U-Boot.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add CPU function to register and initialize the dw_mmc SD controller.
This allows us to use the HPS SDMMC block.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add function to initialize the EMAC blocks upon board startup.
The preprocessor guards against building on SoCFPGA-VT and against
SPL build are not needed as those are handled implicitly via both
SPL framework and the socfpga_cyclone5.h config file, which will
not define CONFIG_DESIGNWARE_ETH if building for SoCFPGA-VT.
We cannot handle two EMAC ethernet blocks yet, therefore the ifdefs.
Once there is hardware using both EMAC blocks, this ifdef will have
to go.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
This adds watchdog disable. It is neccessary for running Linux kernel.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move RSTMGR_PERMODRST_L4WD0_LSB to reset_manager.h
Reset watchdog only if CONFIG_HW_WATCHDOG is undefined (the default)
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <pavel@denx.de>
To move the arch common function away from board folder to
arch/arm/cpu/armv7/socfpga folder. Its to avoid code duplication
for other non Altera dev kit which is using socfpga device.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Consolidating reset code into reset_manager.c. Also
separating reset configuration for virtual target and
real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Add minimal support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Tom Trini <trini@ti.com>
Cc: Wolfgang Denx <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
----
v8: Remove no_return attribute for reset_cpu
Based on v2012.10-rc2
Anatolij Gustschin
Marek Vasut
Dinh Nguyen
Masahiro Yamada
Simon Glass
Stefan Roese
Pavel Machek
Chin Liang See
Wolfgang Denk
Dinh Nguyen