There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This option only complicates the code unnecessarily, just use
CONFIG_SYS_DEF_EEPROM_ADDR as the default address if there are
only five arguments to eeprom {read/write} if this is defined.
If CONFIG_SYS_DEF_EEPROM_ADDR is not defined, we mandate all
six arguments.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
It should be after the u-boot reserved sectors and before the env
sectors, since the solution used for kmvect1 (tell the linker to put the
firmware into the u-boot produced binary, at the end of the area) should
be the exception.
The #define is only "conditional" so that we can still support kmvect1.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The hardcoded value are bad, since the address could change between
different boards.
Furthermore, the relevant #defines are set only if #undefined here, so
that they can be changed by some boards if required.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
For consistency with all the other km83xx plaforms, this should also be
defined for km8309. The same settings as for km8321 are taken.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
On the km8321 boards is CONFIG_SYS_DDRCDR not defined, which leads to
the DDRCDR not being configured at startup and still containing the
reset value.
The required settings for our km8321 hardware designs are different than
the reset value and must be set with CONFIG_SYS_DDRCDR, that is used
by mpc83xx's cpu_init_f function at early CPU initialization.
The important settings are the DDR2 internal voltage level and the
half-strength "drivers".
In our case where the DRAM chips are soldered on board and the routing
for these signals under control, half-strength is sufficient as a few
measurements done in the lasts have shown. Since all the hardware
qualification tests have been performed with half strength, the nominal
strength settings are removed in favor of the default reset half
strength settings.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
We use the same settings for open firmware defines on all our powerpc
targets, so move them from the CPU specific headers to the common
powerpc header.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
128kByte and 3,986MB may be in the future too little for kernel the fdt
blob respectively the kernel image. So increase the reserved areas here,
we have the space for this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
If a DTB is found with cramfsls, the bootscript continues as expected.
If none is found, the cramfsloadfdt and boot subbootcmds are updated to
not load the DTB from cramfs and not pass it to the kernel. The kernel
thus must have an appended DTB otherwise the boot will fail.
This is required for the km_kirkwood boards that must support .esw where
the DTB sometimes is appended (for backwards compatibility) and sometimes
is passed correctly (as we do now for all newer boards).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
To prevent u-boot to stop accidently e.g. due to line noise on the
serial line, we now use the option CONFIG_AUTOBOOT_KEYED. We choose the
<SPACE> key for this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
KM_ENV_BUS was used for nothing else than an direct assignment to
CONFIG_I2C_ENV_EEPROM_BUS. To avoid this, directly use
CONFIG_I2C_ENV_EEPROM_BUS instead.
Patchwork: http://patchwork.ozlabs.org/patch/399411/
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Another shell scripting command that has not been moved.
Moved using tools/moveconfig.py using these settings:
CMD_SETEXPR bool n y
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This converts all the Keymile powerpc boards to the generic board
initialization.
This includes the 3 Keymile powerpc subsystems: km82xx, km83xx,
and kmp204x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.
Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This implies that all the km_kirkwood boards and their variants now are
using the generic board init sequence.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
When u-boot initializes the RAM (early in boot) it looks for the "pram"
env variable to know which is area it cannot use. If the "pram" env variable
is not found, the default CONFIG_PRAM value is used.
This value used to be 0 (no protection at all). This patch sets it to a
value that covers PHRAM and PNVRAM that must be protected in our case.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The booting of the board is now protected by the CPU watchdog.
A failure during the boot phase will end up in board reset.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
a script by setting the active bank to testbank
The post_hotkeys_pressed return the state of the SELFTEST pin.
The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.
Finally, the unused #defines for the not so relevant mtest command are
removed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
CONFIG_SYS_GBL_DATA_SIZE is not used any more.
The size of struct "global_data" is automatically calculated
by asm-offsets. (See lib/asm-offsets.c)
GENERATED_GBL_DATA_SIZE should be used instead of
CONFIG_SYS_GBL_DATA_SIZE.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.
We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available
For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.
Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".
Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt" [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]
This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.
The machid was left unchanged, this should keep compatibility with both
older and newer kernels.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This is needed for board specific additional environment variables.
E.g. the mgcoge3un has this additional "waitforne" variable.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The new prototype and the final series was moved from Micron to Spansion
to have a better reset sequence that is easier to support.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.
This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.
The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_MPC83xx in board config headers
because it is defined in arch/powerpc/cpu/mpc83xx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG.
Also add their details in README.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
care about this parameter or it should be gone completely.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Bin Meng
Marek Vasut
Thomas Chou
Valentin Longchamp
Holger Brunck
Masahiro Yamada
Simon Glass
Joe Hershberger
Peter Tyser
Kim Phillips
Masahiro Yamada
Jeffrey Ladouceur
Boschung, Rainer
Zhao Qiang
Gerlando Falauto
Prabhakar Kushwaha
Vladimir Zapolskiy
York Sun
Rob Herring