- i2c addresses for the videoboard port expanders were
wrong.
- the fpga reset signal was not initialized.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
DP501 only supports DP 1.1a.
Limit settings for link bandwidth and lane count to
values allowed by DP 1.1a.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
With Club 3D dual link adapter there are AUX-channel timeouts
when EDID is read. Increasing retry interval time to max (400us)
fixes this.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
On the BeagleBone these i2c1 pins are routed to the expanasion header, where
they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1
Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
CC: Tom Rini <trini@konsulko.com>
Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.
So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.
We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Support lcdif display:
1. Add pinmux and pad settings for LCDIF
2. Introduce setup_lcd to do the settings for LCDIF
3. Enable VIDEO related macros in board header files
4. Add a new env videomode which is needed by mxsfb.c. The
settings for videomode in this patch is for TFT43AB.
5. Tested on mx6ul 14x14/9x9 evk.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
board_mxsfb_system_setup must be renamed mxsfb_system_setup.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
ls1043ardb_nand_defconfig and ls1043ardb_sdcard_defconfig are missing
in the MAINTAINERS file, so add them for completeness.
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
A few config files have been added without updating MAINTAINERS.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
In 522b021 we dropped 'PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4)' lines in
the mpc85xx linker scripts as this is not required and breaks newer
binutils. This commit cleans up the rest of the powerpc linker scripts.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few config files have been added without updating MAINTAINERS.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.
Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
qe-tdm is muxed with diu, if hwconfig setted as qe-tdm,
assign muxed pins to qe-tdm, then delete diu node from
device tree.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch will fix these checkpatch issues.
CHECK: Alignment should match open parenthesis
+ printf("Enter: %s %s\n", mode_name[mode][0],
+ mode_info[mode]);
CHECK: Alignment should match open parenthesis
+ lcd_printf("\n\n\t%s %s\n", mode_name[mode][0],
+ mode_info[mode]);
CHECK: Alignment should match open parenthesis
+ lcd_printf("\t%s %s - %s\n\n", selection[i],
+ mode_name[i][0],
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch will fix these checkpatch issues.
+static const char *mmc_regulators[] = {
CHECK: Blank lines aren't necessary before a close brace '}'
+
+}
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch will fix these checkpatch issues.
ERROR: spaces required around that '==' (ctx:VxV)
+#if FCLK_SPEED==0 /* Fout = 203MHz, Fin = 12MHz for Audio */
ERROR: spaces required around that '==' (ctx:VxV)
+#elif FCLK_SPEED==1 /* Fout = 202.8MHz */
ERROR: spaces required around that '==' (ctx:VxV)
+#if USB_CLOCK==0
ERROR: spaces required around that '==' (ctx:VxV)
+#elif USB_CLOCK==1
CHECK: spaces required around that ':' (ctx:VxV)
+ "bne 1b":"=r" (loops):"0" (loops));
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adds additional file with implementation of board
detection code for Odroid-XU3/XU4.
The detection depends on compatible found in fdt:
- "samsung,exynos5" - uses Exynos5 generic code
- "samsung,odroidxu3" - try detect XU3 revision
There are few revisions of Odroid XU3/XU4, each can be detected
by checking the value of channel 9 of built-in ADC:
Rev ADC Board
0.1 0 XU3 0.1
0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT
0.3 1280 XU4 0.1
The detection code depends on the ADC+10% value.
Implementation of functions:
- set_board_type() - read ADC and set type
- get_board_rev() - returns board revision: 1..3
- get_board_type() - returns board type string
Additional functions with return values of bool:
- board_is_generic() - true if found compatible "samsung,exynos5"
but not "samsung,odroidxu3"
- board_is_odroidxu3() - true if found compatible "samsung,odroidxu3"
and one of XU3 revision.
- board_is_odroidxu4() - true if found compatible "samsung,odroidxu3"
and XU4 revision.
After I2C controller init, the get_board_type() can check
if the XU3 board is a "Lite" variant, by probing chip
0x40 on I2C0 (INA231 - exists only on non-lite).
This is useful for setting fdt file name at misc_init_r().
Enabled configs:
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- CONFIG_ODROID_REV_AIN
- CONFIG_REVISION_TAG
- CONFIG_BOARD_TYPES
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The function get_board_type() is called in two places by common code,
but the returned pointer was never check.
This commit adds checking the returned pointer, before use it.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It will take more than 1s when wake up from deep sleep. Most of the
time is spent on outputing information. This patch reduced the deep
sleep latency by:
1. avoid outputing system informaton
2. remove flush cache after DDR restore
3. skip reloading second stage uboot binary when SD boot
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The ITS bit was being read incorrectly beacause of operator
precedence. The same ahs been corrected.
Signed-off-by: Lawish Deshmukh <lawish.deshmukh@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Dirk Eibach
Reinhard Pfau
robertcnelson@gmail.com
Hannes Petermaier
Peng Fan
Fabio Estevam
Alexandre Courbot
Stephen Warren
Thomas Chou
Tom Rini
Albert ARIBAUD
Bin Meng
Andy Fleming
Michal Simek
Daniel Gorsulowski
Yangbo Lu
Zhao Qiang
Minkyu Kang
Przemyslaw Marczak
tang yuantian
Aneesh Bansal