This patch adds the driver of altera spi controller, which is
used as epcs/spi flash controller. It also works with mmc_spi
driver.
This driver support more than one spi bus, with base list declared
#define CONFIG_SYS_ALTERA_SPI_LIST { BASE_0,BASE_1,... }
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This adds a driver for the SPI controller found on davinci
based SoCs from Texas Instruments.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This adds a driver for the SPI controller found on davinci
based SoCs from Texas Instruments.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.
Changed in v4:
- Update to new API
- Handle zero-length transfers appropriately. The user may send a
zero-length SPI transfer with SPI_XFER_END set in order to
deactivate the chip select after a series of transfers with chip
select active. This is useful e.g. when polling the status
register of DataFlash.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This is an SPI driver for i.MX and MXC based SoCs from Freescale. So far
only implemented and tested on i.MX31, can with a modified register layout
and definitions be used for i.MX27, I think, MXC CPUs have similar SPI
controllers too.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family. Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move the initialization of the LAWs into C code and provide an API
to allow modification of LAWs after init.
Board code is responsible to provide a law_table and num_law_entries.
We should be able to use the same code on 86xx as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Renamed mcfserial.c to mcfuart.c. Modified Makefile for mcfuart.o from mcfserial.o. Replace immap_5329.h and m5329.h to immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
Thomas Chou
Sekhar Nori
TsiChung Liew
Prafulla Wadaskar
Grzegorz Bernacki
Jean-Christophe PLAGNIOL-VILLARD
Mike Frysinger
Ben Warren
Hans-Christian Egtvedt
Guennadi Liakhovetski
Kim Phillips
Kumar Gala
Peter Pearse
TsiChungLiew
Wolfgang Denk
Marian Balakowicz
Bartlomiej Sieka
Wolfgang Denk