The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Since the reset vector is always aligned to a very large boundary, we
can save a couple of KB worth of alignment padding by placing the
exception vectors at the same address.
Deciding which one it is is easy: If we're handling an exception, the
CPU is in Exception mode. If we're starting up after reset, the CPU is
in Supervisor mode. So this adds a very minimal overhead to the reset
path (only executed once) and the exception handling path (normally
never executed at all.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The .flashprog section was only needed back when we were running
directly from flash, and it's even more useless on NGW100 since it
uses the CFI flash driver which never used this workaround in the
first place.
Remove it on STK1000 as well, and get rid of all the associated code and
annotations.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Relocate the u-boot image into SDRAM like everyone else does. This
means that we can handle much larger .data and .bss than we used to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add atstk1002_config target to Makefile and move the AVR32 section
down below Blackfin so that it doesn't end up in the middle of
MIPS.
Drop the autogenerated linker script thing for now. Will have to
revisit how to handle chips with different flash and RAM layout
later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Patch by Haavard Skinnemoen, 06 Sep 2006
This patch adds support for the ATSTK1000 with the ATSTK1002 CPU
daughterboard.
ATSTK1000 is a full-featured development board for AT32AP CPUs. It
has two ethernet ports, a high quality QVGA LCD panel, a loudspeaker,
and connectors for USART, PS/2, VGA, USB, MMC/SD cards and
CompactFlash cards. For more information, please see this page:
http://www.atmel.com/dyn/products/tools.asp?family_id=682
The ATSTK1002 is a daughterboard for the ATSTK1000 supporting the
AT32AP7000 chip.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
- Add support for the SSV ADNP/ESC1 (Nios Softcore)
* Patch by George G. Davis, 9 Mar 2004:
fix recent build failure for SA1100 target
* Patch by Travis Sawyer, 09 Mar 2004:
Support native interrupt mode for the IBM440GX.
Previously it was running in 440GP compatibility mode.
- more documentation for NIOS port
- new struct nios_pio_t, struct nios_spi_t
- Reconfiguration for NIOS Development Kit DK1C20:
o move board related code from board/dk1c20
to board/altera/dk1c20
o create a new common source path board/altera/common
and move generic flash access stuff into it
o change/expand configuration file DK1C20.h
- Add support for NIOS Development Kit DK1S10
- Add status LED support for NIOS systems
- Add dual 7-segment LED support for Altera NIOS DevKits
- Added Motorola CPU 8540/8560 support (cpu/85xx)
- Added Motorola MPC8540ADS board support (board/mpc8540ads)
- Added Motorola MPC8560ADS board support (board/mpc8560ads)
* Minor code cleanup
- add support for Altera Nios-32 CPU
- add support for Nios Cyclone Development Kit (DK-1C20)
* Patch by Steven Scholz, 29 Sep 2003:
- A second parameter for bootm overwrites the load address for
"Standalone Application" images.
- bootm sets environment variable "filesize" to the resulting
(uncompressed) data length for "Standalone Application" images
when autostart is set to "no". Now you can do something like
if bootm $fpgadata $some_free_ram ; then
fpga load 0 $some_free_ram $filesize
fi
* Patch by Denis Peter, 25 Sept 2003:
add support for the MIP405 Rev. C board
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
Add IDMA example code (tested on 8260 only)
* Add support for Purple Board (MIPS64 5Kc)
* Add support for MIPS64 5Kc CPUs
* Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS
* Patch by Denis Peter, 04 Apr 2003:
- update MIP405-4 board
* Patches by Denis Peter, 03 April 2003:
- fix PCI IRQs on MPL boards
- fix two more un-relocated pointer problems
* Fix behaviour of "run" command:
- print error message iv variable does not exist
- terminate processing of arguments in case of error
* Patches by Peter Figuli, 10 Mar 2003
- Add support for BTUART on PXA platform
- Add support for WEP EP250 (PXA) board
* Fix flash problems on INCA-IP; add tool to allow bruning images to
flash using a BDI2000
* Implement fix for I2C Edge Conditions problem for all boards that
use the bit-banging driver (common/soft_i2c.c)
* Add patches by Robert Schwebel, 31 Mar 2003:
- csb226 board: bring in sync with innokom/memsetup.S
- csb226 board: fix MDREFR handling
- misc doc fixes / extensions
- innokom board: cleanup, MDREFR fix in memsetup.S, config update
- add BOOT_PROGRESS to armlinux.c
- fix bug in BOOTP code (must use NetCopyIP)
- update of CSB226 port
- clear BSS segment on XScale
- added support for i2c_init_board() function
- update to the Innokom plattform
* Extend support for redundand environments for configurations where
environment size < sector size
Mark Jackson
Haavard Skinnemoen
Haavard Skinnemoen
Wolfgang Denk
Wolfgang Denk
wdenk