This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.
This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.
This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.
Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:
AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz
33MHz async PCI frequency:
PLB = 133:
=> 32 <= 44.3 <= 65 (div = 3)
PLB = 166:
=> 32 <= 55.3 <= 65 (div = 3)
66MHz async PCI frequency:
PLB = 133:
=> 65 <= 66.5 <= 132 (div = 2)
PLB = 166:
=> 65 <= 83 <= 132 (div = 2)
Signed-off-by: Stefan Roese <sr@denx.de>
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Signed-off-by: Stefan Roese <sr@denx.de>
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.
Here the details of this patch:
o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
board-specific settings. As an example the sequoia board requires 0.
Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
CFG_PCI_CACHE_LINE_SIZE to 0.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 533 nor ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand ;to configure the board for 667MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.
Signed-off-by: Stefan Roese <sr@denx.de>
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
for the 4k NAND boot image so define bus_frequency to 133MHz here
which is save for the refresh counter setup.
Signed-off-by: Stefan Roese <sr@denx.de>
As provided by the AMCC applications team, this patch optimizes the
DDR2 setup for 166MHz bus speed. The values provided are also save
to use on a "normal" 133MHz PLB bus system. Only the refresh counter
setup has to be adjusted as done in this patch.
For this the NAND booting version had to include the "speed.c" file
from the cpu/ppc4xx directory. With this addition the NAND SPL image
will just fit into the 4kbytes of program space. gcc version 4.x as
provided with ELDK 4.x is needed to generate this optimized code.
Signed-off-by: Stefan Roese <sr@denx.de>
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
Larry Johnson
Stefan Roese
Gary Jennejohn
Niklaus Giger
Igor Lisitsin
Jeffrey Mann
John Otken john@softadvances.com
Marian Balakowicz
Wolfgang Denk