causing inrush currents which as a result, shut down the AXP209. This
has been reported before, without knowing the actual cause.
A fix appeared to be done with commit 0e6e34ac8d ("sunxi: Olimex A20
boards: Enable LDO3 and LDO4 regulators").
The description there is a bit misleading, the kernel does not hang
during AXP209 initialization, the PMIC shuts down, causing voltages to
drop and thus the whole system to freeze.
While the AXP209 does have the ability to ramp up the voltage slowly, to
reduce these inrush currents, the voltage rate control (VRC) however is
not applicable when switching on the LDO3 output. Only when going from
an enabled lower voltage setting, to a higher voltage setting is the VRC
in effect.
To work around this problem, we set LDO3 to the lowest possible setting
of 0.7 V if it was not yet enabled, and then let the VRC (if enabled) do
its thing. It should be noted, that for some undocumented reason, there
is a short delay needed between setting the LDO3 voltage register and
enabling the power. One would expect that this delay ought to be just
after enabling the output power at 0.7 V, but this did not work.
This allows for the power to gradually rise to the desired voltage,
instead of spiking up quickly. Reason to have this can be to reduce the
inrush currents for example.
There are 3 slopes to choose from, the default, 'none' is a voltage rise
of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise.
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.
In fact, GCC 8.1.0 reports a warning against it:
error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]
Fix it by using the correct size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
So far the TSC timer driver supports trying hardware calibration first
and using device tree as last resort for its running frequency as the
normal timer.
However when it is used as the early timer, it only supports hardware
calibration and if it fails, the driver just panics. This introduces
a new config option to specify the early timer frequency in MHz and
it should be equal to the value described in the device tree.
Without this patch, the travis-ci testing on QEMU x86_64 target fails
each time after it finishes the 'bootefi selftest' as the test.py see
an error was emitted on the console like this:
TSC frequency is ZERO
resetting ...
### ERROR ### Please RESET the board ###
It's strange that this error is consistently seen on the travis-ci
machine, but only occasionally seen on my local machine (maybe 1 out
of 10). Since QEMU x86_64 target enables BOOTSTAGE support which uses
early timer, with this fix it should work without any failure.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In initr_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us(). This call happens before initr_dm(), which inits driver
model.
On x86 we set gd->timer to NULL in the transition from board_init_f()
to board_init_r(). See board_init_f_r() for this assignment. So U-Boot
knows there is no timer available in the period immediately after
relocation.
On x86 the timer_get_us() call is implemented as calls to get_ticks() and
get_tbclk(). Both of these call dm_timer_init() to set up the timer, if
gd->timer is NULL and the early timer is not available.
However dm_timer_init() cannot succeed before initr_dm() is called.
So it seems that on x86 if we want to use CONFIG_BOOTSTAGE we must enable
CONFIG_TIMER_EARLY. Update the Kconfig to handle this.
Note: On most architectures we can rely on the pre-relocation memory still
being available, so that gd->timer pointers to a valid timer device and
everything works correctly. Admittedly this is not strictly correct since
the timer device is set up by pre-relocation U-Boot, but normally this is
fine. On x86 the 'CAR' (cache-as-RAM) memory used by pre-relocation U-Boot
disappears in board_init_f_r() and any attempt to access it will hang.
This is the reason why we must mark the timer as invalid when we get to
board_init_f_r().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The PCI controller can have DT subnodes describing extra properties
of particular PCI devices, ie. a PHY attached to an EHCI controller
on a PCI bus. This patch parses those DT subnodes and assigns a node
to the PCI device instance, so that the driver can extract details
from that node and ie. configure the PHY using the PHY subsystem.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add new Kconfig option, SYS_BOOTCOUNT_MAGIC, to select the boot
counter magic word. This can be useful ie. in case the entire
boot counter register is not usable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Xilinx SoC Versal is using fixed clock where setting rate is not supported.
That's why workaround the driver till real clock driver is supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to #ifdef some variables to avoid warning about them being
unused.
Fixes: 1a048cd656 ("driver: net: fsl-mc: Add support of multiple phys for dpmac")
Signed-off-by: Tom Rini <trini@konsulko.com>
NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.
So macro for this micron manufacturer id.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
accidentially while fixing merge errors for patch:
https://lists.denx.de/pipermail/u-boot/2018-September/342278.html
missed to add files:
MAINTAINERS
drivers/i2c/Kconfig
drivers/i2c/Makefile
add them with this patch.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.
i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The dpmac initalization should not depend on phy.
As the phy is not necessary to be present for dpmac to function.
Therefore, remove dpmac initialization dependency from phy.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
when there is no phy present for a dpmac, a dummy phy device is created.
when we move to multiple phy method, we need to create as many dummy phy
devices.
Change this method so that we don't need to create dummy phy devices.
We always report linkup if no phy is present.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if an error occurs during init_phy, we should free the phydev structure
which has been allocated by phy_connect.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The phydev structure is present in both ldpaa_eth_priv and
wriop_dpmac_info. the phydev in wriop_dpmac_info is not being used
As the phydev is created based on phy_addr and bus members of
wriop_dpmac_info, it is appropriate to keep phydev in wriop_dpmac_info.
Also phy_regs is not being used, therefore remove it
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Push generic defines of gpio.h out of mach-davinci to drivers/gpio
now that non-davinci architectures are beginning to use this IP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix calimain build]
Signed-off-by: Tom Rini <trini@konsulko.com>
The goto label name is misspelled it should be DPMAC not DPAMC
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The target will respond to pings while doing other network handling.
Make sure that the response happens and is correct.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This tests that ARP requests made to this target's IP address are
responded-to by the target when it is doing other networking operations.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tests need to be able to pass their "unit test state" to the handlers
where asserts are evaluated. Add a function that allows the tests to set
this private data on the sandbox eth device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use up to the max allocated receive buffers so as to be able to test
more complex situations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If tests want to implement tx handlers, they will likely need access to
the details in the priv structure.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make the send handler registerable so tests can check for different
things.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Store the per-device data with the device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The DP83867 has a muxing option for the CLK_OUT pin. It is possible
to set CLK_OUT for different channels.
Create a binding to select a specific clock for CLK_OUT pin.
Based on commit 9708fb630d19 ("net: phy: dp83867: Add binding for
the CLK_OUT pin muxing option") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Based on commit ac6e058b75be ("net: phy: dp83867: Recover from "port mirroring"
N/A MODE4") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Davanci spi driver has DM support already, this patch
add support for platdata so-that SPL can use it for
low foot-print.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com>
Some boards (like omap3_logic) hang when trying to access
address 0. This happens when executing the new 'mtd list' command.
This patch enhances the checks for conditions that would
preclude mtd_probe_devices() from operating.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently there are two ethernet drivers (mvneta.c and mvpp2.c) that
has netdev_### (eg: netdev_dbg) log macros defined in its own driver
file. This adds these log macros in a common place linux/compat.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The internal DMAC on Gen3 is 32bit only, limit the DMA address
range to 32bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Pass the entire source data pointer to tmio_sd_addr_is_dmaable()
so we don't have to apply casts throughout the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
At present this function uses pixels but it seems more useful for it to
position in terms of characters on the screen. This also matches the
comment to the function. Update this.
Unfortunately there is one user of this function (at91). Have a crack at
fixing this, since I cannot test it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
We have a method to return the last reset as a string for humans, but not
a method that allows it to be used programmatically. Add a new method that
returns the last reset as an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ctags emits lines with unmatched quotes which means that the
output file is invalid. This is with exuberant-ctags version 5.9~svn201103
but I also see it with plain ctags. I am not sure that it is a bug though.
Make a few minor changes in the source code to fix this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the panel can be turned on but not off, and the brightness
cannot be controlled at run-time. Add a new API function to both the panel
and backlight uclasses to handle this. Enhance the PWM backlight driver
to deal with custom levels properly and allow the backlight to be turned
on and off.
Update the test to cover thes new features.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this uclass has no tests. Add a simple one which checks the PWM
configuration, regulator and GPIO.
Signed-off-by: Simon Glass <sjg@chromium.org>
Merlijn Wajer
Cédric Le Goater
Bin Meng
Simon Glass
Marek Vasut
Adam Ford
Marek Vasut
Michal Simek
Tom Rini
Ashish Kumar
Heiko Schocher
Pankaj Bansal
Keerthy
Joe Hershberger
Janine Hagemann
Jagan Teki
Marek Vasut