Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified. This has been tested
on AM335x GP EVM and Beaglebone White.
[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Added chip type detection and twl6032
support in the battery control
and charge functions.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
The data struct is used to support different
PMIC chip types. It contains the chip type and
the data (e.g. registers addresses, adc multiplier)
which is different for twl6030 and twl6032.
Replaced some hardcoded values with the
structure vars.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
The struct incorrectly referenced SMPS1 for all three power
domains. Fixed this by using SMPS2 and SMPS5 as appropriate.
Add some comments and choose voltage values that correspond
to voltage selection codes.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on
the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and
pcm051_rev1 for the old RAM configuration. Board revision 2 has to use
pcm051_rev1 also.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Add support for the 16 bits pca9555 i2c to gpio extender featured
by the SB-T335 baseboard.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Adding Freeze Controller driver. All HPS IOs need to be
in freeze state during pin mux or IO buffer configuration.
It is to avoid any glitch which might happen
during the configuration from propagating to external devices.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.
So move CONFIG_SYS_NO_FLASH definition to proper position.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The MPDDRC supports different type of SDRAM
This patch add ddr2 initialization function
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable the PIO peripherals early than other peripherals.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The offset of MULA field in PLLA register in sama5d3 is 18,
and the length only 7 bits.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The PLLADIV2 bit is not defined in at91sam9261 SoC, so remove it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As the DBGU and PIT has its own ID on sama5d3 SoC, while not share
with SYS ID. So, correct them.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The SAMA5D36 chip is the superset product of SAMA5D3x family.
For detail information please refer to:
http://www.atmel.com/Microsite/sama5d3/default.aspx
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since the required API is gpio which is enclosed with CONFIG_ATMEL_LEGACY use
that switch here.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Heiko Schocher <hs@denx.de>
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
- add splashpos=m,m to default environment, so splash screen is always
centered.
- adapt environment for bootcount feature
- add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
store the bootcount in the environment, as we have no softreset
save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
Add for the siemens boards the possibility to define in dfu mode,
the iSerialNumber and the bcdDevice fields in the USB Device
descriptor.
- fix upgrade mechanism based on bootcount
Correct location of saveenv and remove not active variable.
Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
reboot board in case of empty kernel partition. Without
these defines an empty kernel partition leads to an
abort of boot process and one remains in u-boot prompt.
- general cleanup of dxr2, pxm2 and rut boards
all:
* Remove net boot from bootcmd
Ping can cause a crash on boards without ethernet phy.
net_nfs command is used only for development
* Add reset at the end of bootcmd
In order to have an immediate reset of the boot when bootcmd
fails, add reset at the end of bootcmd.
rut:
* add nand_img_size
dxr2:
* update nand_img_size
* ddr3 timings updated with iocontrol property that can be
modified via eeprom. New default parameters from software
leveling with draco ES2.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>
add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility. So add
another symbol for the bootcount driver for the IP block.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Switch to using the generic gpio_led driver instead of the private to
cm_t35 board led implementation.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Commit f6d1f6e4a5 broke selection of UARTs
other than UART0 for am335x_evm configurations by setting CONS_INDEX to
1 for all configurations. Revert the CONS_INDEX changes.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Update my email address as ti814x_evm maintainer to save
people some frustrating bounces and non-response.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"
enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is introduced. If "upgrade_available" is
0, "bootcount" is always 0 therefore no need to save the
environment on u-boot boot, if "upgrade_available" is 1 "bootcount"
is incremented in the environment and environment gets written
on u-boot start.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0 (for example with fw_setenv),
if a boot was successfully.
Signed-off-by: Heiko Schocher <hs@denx.de>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
A weak annotation is needed in order to prevent link errors when
get_ticks is overridden. This fixes sandbox build.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX
Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The env export command doesn't export the first variable of the list
since commit 5a31ea04c9
"env grep" - reimplement command using hexport_r()
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
As originally implemented, setting the AUTOBOOT_KEYED config option will
prevent users from breaking into the autoboot script with ctrl-c. Restore
that option with a new config symbol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Staticize local functions in xuartlite driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Curently memcpy copies string without null terminating char because
function strlen returns only number of characters excluding
null terminating character. Replace memcpy with strcpy.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Tom Rini <trini@ti.com>
Tom Rini
Oleg Kosheliev
Lubomir Popov
Lars Poeschel
Ilya Ledvich
Chin Liang See
Albert ARIBAUD
Jens Scharsig (BuS Elektronik)
Bo Shen
Heiko Schocher
Wu, Josh
Andreas Bießmann
Samuel Egli
Igor Grinberg
Andrew Bradford
Matt Porter
Rob Herring
Suriyan Ramasami
Axel Lin
Pierre Aubert
Mark Langsdorf
Piotr Wilczek
Luka Perkov