The function interrupt_init_cpu() is given an int return type but does
not return anything but 0. Rework this to be a void function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
The overflow calculation was incorrect. Adding the start block of the
partition is not needed because the sectors are already relative to the
beginning of the partition. If you attempted to write a file smaller
than cur_part_info.start blocks on a full partition the old calculation
fails to catch the overflow. This would cause an infinite loop in the
determine_fatent function.
Old, incorrect calculation:
ending sector of new file = start sector + file size (in sectors)
last sector = partition start + total sectors on the partition
Adding the partition start block number is not needed because sectors
are already relative to the start of the partition.
New calculation:
ending sector of new file = start sector + file size (in sectors)
last sector = total sectors on the partition
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
This re-syncs AM33xx DTS file with current file from
Linux v4.13-rc4 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from mmc,
mac, lcdc and tscadc sub nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is currently disabled, so USB keyboards are not detected in U-Boot.
Enable this option to fix that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Paul Barker <pbarker@toganlabs.com>
Otherwise:
drivers/usb/gadget/f_fastboot.c:564:32: warning: format "%lx" expects
argument of type "long unsigned int", but argument 3 has type "unsigned
int" [-Wformat=]
Signed-off-by: Tom Rini <trini@konsulko.com>
The db-88f6820-amc has four chips with 2Gb density giving a total of 1GB
DRAM. Update the board_topology_map to reflect the correct
configuration.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Cc: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building the flash zImage code on aarch64 we see warnings about
pointer size casts. Use uintptr_t instead to correct these.
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-By: Sam Protsenko <semen.protsenko@linaro.org>
There is no guarantee that commands are null-terminated in the USB
request buffer, so limit the length of data that is printed.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Steve Rae <steve.rae@raedomain.com>
Fastboot loads an image at CONFIG_FASTBOOT_BUF_ADDR, but currently
tells do_bootm() to look for an image at $loadaddr. This breaks if
CONFIG_FASTBOOT_BUF_ADDR is different from the current user-set
loadaddr.
Instead, tell do_bootm() to pick up the image where it was laoded.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
With the change to the environment code to remove the common init stage
of pointing to the default environment and setting it as valid, combined
with the change to switch gd->env_valid from 0/1/2 to an enum we now
must set env_valid to one of the enum values rather than an int. And in
this case, not only was setting it to an int wrong, it was now the wrong
value. Finally, in the case of ENV_IS_NOWHERE we must still say that
our envionrment is invalid after init for things to continue to
function.
Fixes: 7938822a6b ("env: Drop common init() functions")
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v3:
- Actually include changes for env/nowhere.c
Since commit 576e3cc700 ("usb: host: xhci-dwc3: Add dual role mode
support from DT"), warning is displayed if dr_mode is not specified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Merge sys_reset data of LD4, Pro4, sLD8 and Pro5
- Merge sys_reset data of LD11 and LD20
- Use primitive UNIPHIER_RESETX() macro because bit assignments for
system reset will be changed for every SoC in the future
- Add NAND and eMMC resets
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 82d075e79f.
Commit 82d075e79f ("ARM: uniphier: fix ROM boot mode for PH1-sLD3")
was a workaround for sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to simplify the init code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit bcc51c1512.
Commit bcc51c1512 ("ARM: uniphier: move lowlevel debug init code
after page table switch") was intended to support lowlevel debug for
sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to enable lowlevel debug earlier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:
$ make uniphier_v8_defconfig
warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)
While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
since commit: b529993e02 "spl: add hierarchical defaults for SPL_LDSCRIPT"
taurus board stopped working. Use the ldscript from
arch/arm/cpu/u-boot-spl.lds (as before this patch) fixed it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
CONFIG_SYS_GENERIC_GLOBAL_DATA is no longer used by any board or
platform, so support for it can be dropped.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ATF can leave the MMC IP in a state where U-Boot mmc driver
can't enumerate the eMMC.
This patch provides a mmc0_reset_clk() function like we
already so do sd card controller which resets the IP
when entering U-Boot.
With this patch applied eMMC partitions are successfully
enumerated again.
=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device
=> mmc part
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000800 0x00000fff "vrl"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 496847ab-56a1-4cd5-a1ad-47f4acf055c9
2 0x00001000 0x000017ff "vrl_backup"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 61a36fc1-8efb-4899-84d8-b61642efa723
3 0x00001800 0x00001fff "mcuimage"
<snip>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Signed-off-by: Tom Rini <trini@konsulko.com>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Signed-off-by: Tom Rini <trini@konsulko.com>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Reported-by: Coverity (CID: 166335)
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that sandbox is building cmd/mtdparts.c Coverity has looked at the
code and found a number of issues. In index_partitions() it is possible
that part will be NULL, so re-work the checks and debug statements to
take this into account. We have a number of string buffers that we
print to in the exact size of, and use string functions on, so we need
to ensure they are large enough to be NULL terminated. In
device_parse() it is not possible for num_partitions to be 0 (we would
have hit a different error first) so remove logically dead code.
Finally, in parse_mtdparts() if we have an error we need to free the
memory allocated to dev.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Coverity (CID: 166334, 166333, 166332, 166329, 166328)
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 089df18bfe ("lib: move hash CONFIG options to Kconfig") moved
CONFIG_SHA1, CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and
CONFIG_SHA_PROG_HW_ACCEL config options to Kconfig. So in the case of
SPL, CONFIG_SPL_HASH_SUPPORT enables CONFIG_SHA1 and CONFIG_SHA256 which
enables SHA SW library by default. But in the case of platforms with
SHA HW library support, SHA SW library becomes redundant and increases
size of SPL by approx 18K. Rework the code so that we have named
members and only have either software or hardware versions of the
algorithm, depending on the relevant config options. Update the comment
around hash_algo to reflect this as well.
Reported-by: Sumit Garg <sumit.garg@nxp.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
On some systems `python` is `python3` (for instance, Archlinux). The
`PYTHON` variable can be used to point to `python2` to have a successful
build.
The use of `PYTHON` is currently limited in the Makefile and needs to be
extended in other places:
First, pylibfdt is required to be a Python 2 binding (binman imports
pylibfdt and is only compatible Python 2), so its setup.py needs to be
called accordingly. An alternative would be to change the libfdt
setup.py shebang to python2, but the binding is actually portable. Also,
it would break on system where there is no such thing as `python2`.
Secondly, the libfdt import checks need to be done against Python 2 as
well since the Python 2 compiled modules (in this case _libdft.so) can
not be imported from Python 3.
Note on the libfdt imports: "@if ! PYTHONPATH=tools $(PYTHON) -c 'import
libfdt'; then..." is probably simpler than the currently sub-optimal
pipe.
Reviewed-by: Jonathan Gray <jsg@jsg.id.au>
Do not dereference bmp before the check if it is NULL.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fix the IOMUX setting for SDcard CMD pin at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dts from kernel is using rk3228-pinctrl as compatible name,
need to sync with it to make the driver work.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The description for eMMC/SDIO/SDMMC src is not correct,
update the CRU_CLKSEL11_CON value definition according to TRM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRAM start address is not 0, so need to update the last bank size
as:
DRAM start addr + DRAM_SIZE - last bank start addr
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdtdec.h is included, but not used in rk3399-board-spl.c: remove the
'#include'-statement.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There are two same gmac node, remove one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
UEFI API functions have different return types.
Some return a value of type EFI_STATUS other don't.
We therefore should not cast the return value of EFI_EXIT
to another type than the expression passed to EFI_EXIT.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Wenyou.Yang@microchip.com
Tom Rini
Reno Farnesi
Suniel Mahesh
Jagan Teki
Simon Glass
Chris Packham
Lukasz Majewski
John Keeping
Peter Chubb
Bin Meng
Masahiro Yamada
Anatolij Gustschin
Andy Shevchenko
Heiko Schocher
Thomas Petazzoni
Peter Griffin
Clément Bœsch
xypron.glpk@gmx.de
Kever Yang
Philipp Tomsich