GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE VDD_MPU
OPP50 OPP50
OPP50 OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz
Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified. This has been tested
on AM335x GP EVM and Beaglebone White.
[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.
Signed-off-by: Pekon Gupta <pekon@ti.com>
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
and include in all board configs using AM33xx SoC platform.
Signed-off-by: Pekon Gupta <pekon@ti.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
Add the support for the am437x xhci usb host.
The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
We can run the DDR at 400MHz, so update the timings for that purpose.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
Starting with PG2.1 we have a register in the CONTROL_MODULE that is set
with the package type and maximum supported frequency. Add this, and
the relevant mask/values.
Signed-off-by: Tom Rini <trini@ti.com>
We need to allow for a further call-out in spl_board_init. Call this
am33xx_spl_board_init and add a __weak version. This function may be
used to scale the MPU frequency up, depending on board needs.
Signed-off-by: Tom Rini <trini@ti.com>
We had been allowing the max size to be larger than actually allowed by
the ROM. Expand the commentary here to explain why we set these
locations.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
the clk_get() function is needed for the da8xx-fb video driver,
which is used on the am3xx based siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.
This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.
Thanks for Lubomir Popov to provide valuable comments to fix this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
Fix the wrong mapping between the DDR I/O control registers on AM33XX
SoCs and the software representation in the SPL code.
The most recent public TRM defines the following DDR I/O control registers
offsets:
* ddr_cmd0_ioctrl : offset 0x44E11404
* ddr_cmd1_ioctrl : offset 0x44E11408
* ddr_cmd2_ioctrl : offset 0x44E1140C
* ddr_data0_ioctrl: offset 0x44E11440
* ddr_data1_ioctrl: offset 0x44E11444
While the struct ddr_cmdtctrl has also some reserved bits in the beginning.
The struct is mapped to the address 0x44E11404. As a result "cm0ioctl" points
to the ddr_cmd1_ioctrl register, "cm1ioctl" to the ddr_cmd2_ioctrl and etc.
Registers ddr_cmd0_ioctrl and ddr_data0_ioctrl are never configured because
of this mapping mismatch.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
The location of valid scratch space is dependent on SoC, so move that
there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space. Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.
Signed-off-by: Tom Rini <trini@ti.com>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
omap_boot_parameters is same and defined for each
soc. So move this to a common place to reuse it
across socs.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs. The timings need a slight
adjustment to be correct in all cases with later revs.
Signed-off-by: Tom Rini <trini@ti.com>
After further testing we can run DDR at 400MHz so update the timings
again.
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
Given that on TI814x we have MMC1/2 swapped, we also need to swap them
in MMC_BOOT_DEVICES_START/END
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
In the case of booting from certain peripherals, such as UART, we must
not see what the device descriptor says for RAW or FAT mode because in
addition to being nonsensical, it leads to a hang. This is why we have
a test currently for the boot mode being within range. The problem
however is that on some platforms we get MMC2_2 as the boot mode and not
the defined value for MMC2, and in others we get the value for MMC2_2.
This is required to fix eMMC booting on omap5_uevm.
Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on
classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC).
Signed-off-by: Tom Rini <trini@ti.com>
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine. Currently we support 1-bit hammign
and 8-bit BCH on HW backend.
In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
Lokesh Vutla
Sekhar Nori
Dan Murphy
Tom Rini
Ilya Ledvich
pekon gupta
Heiko Schocher
Enric Balletbo i Serra
Steve Kipisz
TENART Antoine
Wolfgang Denk
Axel Lin
SRICHARAN R
Matt Porter
Andreas Bießmann