In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.
Signed-off-by: Tom Rini <trini@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
Errata ID:i727
Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.
Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.
This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
The DMM sections can be overlapping with each other, with
sections 3 to 0 having the highest to lowest priority in that
order. There could also be a section that is used trap the
unmapped Tiler entries and this trap section could be
overlapping with the actual sdram area.
So take care of the above scenarios while calculating the
size of the actual ram.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
In 8775471bb, the call to timer_init() was removed from common code
and put in OMAP3 s_init() function. As a result the boot was broken
on OMAP4. This patch adds timer_init() in OMAP4 s_init(), that fix
boot on all OMAP4 boards.
Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com>
Tested-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add the emif configurations required for omap5 soc.Add the
correct ddr part configurations required for omap5 evm board.
EDB8164B3PH from ELPIDA is the part used on the board.
Also changes are done to retain some part of the code
common for OMAP4/5 and keep only the remaining in the Soc
specific directories.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Much of omap4 soc support code can be reused for omap5.
Move them to the omap-common directory to facilitate
this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4460 has a different set of values for the ID code, so moving the
old ones to be related just with 4430.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Moves the early UART clock setup setup_clocks_for_console() from
preloader_console_init() to s_init() of OMAP4.
This is done to prepare for OMAP3 integration.
This patch was posted seperatly to the mailinglist but I decidet - since it is
a prereqesit for this patch to add it. Former port to ML:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
payload size and load address from this header. If the
header is not detected assume u-boot.bin as payload
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.
For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails
This work draws upon previous work done for x-loader by:
Santosh Shilimkar <santosh.shilimkar@ti.com>
Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
DECLARE_GLOBAL_DATA_PTR is currently defined within the scope
of function while it is a global pointer. Change the scope of
definition to replicate it's global scope. This seems to help
gcc 4.5 optimizations as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Calculate the SDRAM size from DMM configuration registers instead of using
hard-coded values. This gives correct values for all different boards.
It's assumed that DMM sections do not overlap memory areas.
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds minimum support for OMAP4. Code which can be shared
between OMAP3 and OMAP4 is placed in arch/arm/cpu/armv7/omap-common
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tom Rini
Lokesh Vutla
SRICHARAN R
Dechesne, Nicolas
Andreas Müller
Chandan Nath
Ricardo Salveti de Araujo
Simon Schwarz
Aneesh V
Nishanth Menon
Wolfgang Denk
Steve Sakoman