UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.
It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.
Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).
The patch is based on the work by Maxim Artamonov.
Signed-off-by: Maxim Artamonov <scn1874@yandex.ru>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The way the ALL variable is used allows for config.mk's to add more
targets themselves without having to clutter up the top level Makefile.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not
CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Building the compression code in lib_generic/ with -O2 rather than -Os
gives a nice speed boost without too much code size increase.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest version of U-Boot got a bit fatter in the BSS section which
caused overflows in the RAM region, so increase the monitor size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The debug tools that interface with the other side of the JTAG console
got much slower when generalizing things, so bump up the default timeout
value on the U-Boot side to cope. Hopefully at some point we can improve
the debug tools to speed things back up.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This script is similar to the netconsole script, but instead works with
the JTAG console device driver that exists on Blackfin parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds a egiga driver for the Marvell Kirkwood SoC's.
Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Acked-by: Stefan Rose <sr@denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Different flavours of DaVinci SOC's have differences in their EMAC IP
This patch does the following
1) Updates base addresses for DM365
2) Updates MDIO frequencies for DM365 and DM646x
3) Update EMAC wrapper registers for DM365 and DM646x
Patch applies to u-boot-net git. the EMAC driver itself
will be updated shortly to add support for DM365 and DM646x
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
From 584b5fbd4abfc43f920cc1c329633e03816e28be Mon Sep 17 00:00:00 2001
From: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Date: Wed, 20 May 2009 18:26:01 -0400
Subject: [PATCH] Standardize the use of MCFFEC_TOUT_LOOP as a udelay(1) loop counter.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The problem is that BOOTP_SIZE uses ETHER_HDR_SIZE which is 14 bytes.
If sending a VLAN tagged frame (when env variable vlan is set) this
should be VLAN_ETHER_HDR_SIZE=18 which is what NetSetEther returns.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option. So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file. This is much simpler than
forcing them to duplicate the rest of the linker script.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF51xF parts have an internal SST SPI flash, so make sure the driver is
enabled by default so we can access it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup
common Blackfin board defines. The common method now is to use config.h,
so convert blackfin-config-post.h to that. Rename the still Blackfin
specific blackfin-config-pre.h to config-pre.h so the naming conventions
at least line up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow boards to easily override the root= and default bootcmd, allow
people to tweak the file used in default bootcmds at runtime via one env
var, and add a stock nandboot command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Jean-Christophe PLAGNIOL-VILLARD
Ilya Yanok
Magnus Lilja
Ilko Iliev
Mike Frysinger
Vivi Li
Wolfgang Denk
Remy Bohmer
Prafulla Wadaskar
s-paulraj@ti.com
Richard Retanubun
Norbert van Bolhuis
Ben Warren
Zach LeRoy
Hoan Hoang