As suggested by Grant Likely this patch enables the Xilinx SystemACE
driver to select 8 or 16bit mode upon startup.
Signed-off-by: Stefan Roese <sr@denx.de>
Some CPUs like PPC, BLACKFIN need sync() to ensure cfi flash write command
is fully finished. The sync() is defined in each CPU's io.h file. For
those CPUs which do not need sync for now, a dummy sync() is defined in
their io.h as well.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch removes some problems when the Xilinx SystemACE driver
is used with 16bit access on an big endian platform (like the
AMCC Katmai).
Signed-off-by: Stefan Roese <sr@denx.de>
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Register read/write does not need to be wrapped in a full function. The
patch replaces them with macros.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Two fixes for the nand_wait() function in
drivers/nand/nand_base.c:
1. Use correct timeouts. The original timeouts in Linux
source are 400ms and 20ms not 40s and 20s
2. Return correct error value in case of timeout. 0 is
interpreted as OK.
Signed-off-by: Rui Sousa <rui.sousa@laposte.net>
Signed-off-by: Stefan Roese <sr@denx.de>
* Adds support for AMD command set Top Boot flash geometry reversal
* Adds support for reading JEDEC Manufacturer ID and Device ID
* Adds support for displaying command set, manufacturer id and
device ids (flinfo)
* Makes flinfo output to be consistent when CFG_FLASH_EMPTY_INFO defined
* Removes outdated change history (refer to git log instead)
Signed-off-by: Tolunay Orkun <listmember@orkun.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
This patch addresses a problem when CONFIG_MTD_NAND_VERIFY_WRITE is
defined
and the write crosses a block boundary. The pointer to the verification
buffer (bufstart) is not being updated to reflect the starting of the
new
block so the verification of the second block fails.
CHANGELOG:
* Fix NAND FLASH page verification across block boundaries
Added a phy initialization to adjust the RGMII RX and TX timing
Always set the R100 bit in 100 BaseT mode regardless of the TSEC mode
Signed-off-by: Nick Spence <nick.spence@freescale.com>
chpart, nboot and NAND subsystem related commands now accept also partition
name to specify offset.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Patch by Haavard Skinnemoen, 06 Sep 2006
This is a first attempt at creating a common serial driver for Atmel
chips. For now, it supports the AT32AP7000 AVR32 chip, but it should
be possible to support AT91RM9200 and other ARM-based chips with some
minor modifications.
There's nothing fundamentally AVR32-specific in this driver, but it
does use some features which are currently only defined for the
AT32AP CPU port:
* pm_get_clock_freq: Obtain the clock frequency of a given domain
* gd->console_uart: A "struct device" containing information about
register mappings, gpio resources and clocks associated with the
UART device.
For more information about these features, please see the "AT32AP
CPU" patch.
Introduced COFIG_FSL_I2C to select the common FSL I2C driver.
And removed hard i2c path from a few u-boot.lds scipts too.
Minor whitespace cleanups along the way.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
conditional expressions instead.
Use consistent return code 0/-1 for good/bad indicators.
Include one fewer file if the driver isn't used at all.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
- JFFS2 related commands implemented in mtd-utils style
- Support for bad blocks
- Bad block testing commands
- NAND lock commands
Please take a look at doc/README.nand for more details
Patch by Guido Classen, 10 Oct 2006
* Added support for using eTSEC 3 and eTSEC 4 on the 8548 CDS.
This will only work on rev 1.3 boards (but doesn't break older boards)
* Cleaned up some comments to reflect the expanded role of tsec
in other systems
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
Michal Simek
Wolfgang Denk
Stefan Roese
Haiying Wang
Grant Likely
Heiko Schocher
Stefano Babic
Joakim Tjernlund
Kim Phillips
Timur Tabi
Dave Liu
Nick Spence
Ben Warren
Jon Loeliger
Wolfgang Denk
Andy Fleming
Marian Balakowicz
Jin Zhengxiong
Wolfgang Denk
Matthew McClintock