Move usb device-tree fixup framework from ehci-fsl.c to common place so
that it can be used by other drivers as well (xhci-fsl.c).
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
The dm usb_kbd_remove function() will deregister the usb keyboard for
us on a "usb reset" / "usb stop" so there is no need to manually call
usb_kbd_deregister() in the dm case.
This commit removes usb_kbd_deregister() in the dm case fixing the
following "usb reset" errors:
usb_kbd_remove: warning, ret=-6
device_remove: Device 'usb_kbd' failed to remove, but children are gone
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit fixes crash on BananaPi (and possibly others)
casued by 3f9f8a5b83.
Crash reason:
When no ops were passed to ehci_register(), USB host driver caused
NULL pointer dereference.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
This driver adds support of PIC32 MUSB OTG controller as dual role device.
It implements platform specific glue to reuse musb core.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
ARM defines __raw_writes[bwql], __raw_reads[bwql] in arch io.h
but not the writes[bwql], reads[bwql] needed by some drivers.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
To enable DM on MPC85xx, we need pre-relocation malloc, which is
implemented in this patch.
We also make sure that the IVORs are always 4-aligned on e500 to prevent
alignment exceptions caused by code changes in start.S.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_SYS_INIT_RAM_SIZE may be used out of the board header file.
Some boards use CONFIG_SYS_INIT_RAM_END for the same purpose. To
unify the macros, use CONFIG_SYS_INIT_RAM_SIZE for all.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mario Six <mario.six@gdsys.cc>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
The commands for the VSC9953 l2 switch from T1040 became generic in
patch https://patchwork.ozlabs.org/patch/499748/ and the define
was renamed.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch aims to fix the order of CSU slave index for the LS1021a
board.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When switching between the early and final mmu tables, the stack will
get corrupted if the Non-Secure attribute is different. For ls1043a,
this issue is currently masked because flush_dcache_all is called
before the switch when CONFIG_SYS_DPAA_FMAN is defined.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When setting fixed-link property to DTS, the values should be converted
with using cpu_to_fdt32 so that to have correct value on little endian
Soc.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SerDes protocols might not enable all l2switch ports. In this case,
these ports should not be configured to perform Rx/Tx operations.
This also fixes an issue when flooded frames were also switched to
disabled ports and frames start to accumulate, consuming memory
and eventually causing head-of-line blocking for other frames.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
We can use phys_addr_to for esdhc_base to discard
the #ifdef.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Support Driver Model for fsl esdhc driver.
1. Introduce a new structure struct fsl_esdhc_priv
2. Refactor fsl_esdhc_initialize which is originally used by board code.
- Introduce fsl_esdhc_init to be common usage for DM and non-DM
- Introduce fsl_esdhc_cfg_to_priv to build the bridge for non-DM part.
- The original API for board code is still there, but we use
'fsl_esdhc_cfg_to_priv' and 'fsl_esdhc_init' to serve it.
3. All the functions are changed to use 'struct fsl_esdhc_priv', except
fsl_esdhc_initialize.
4. Since clk driver is not implemented, use mxc_get_clock to geth
the clk and fill 'priv->sdhc_clk'.
Has been tested on i.MX6UL 14X14 EVK board:
"
=>dm tree
....
simple_bus [ + ] | `-- aips-bus@02100000
mmc [ + ] | |-- usdhc@02190000
mmc [ + ] | |-- usdhc@02194000
....
=> mmc list
FSL_SDHC: 0 (SD)
FSL_SDHC: 1 (SD)
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Hector Palacios <hector.palacios@digi.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-By: Eric Nelson <eric@nelint.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.
The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jteki@openedev.com>
PCS auto negotaiation bit should be enabled
along with SGMII autonegotation enabled
in phy.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII to TI phy dp838367
Enable the SGMII and PCS settings in phy
control, CFG2 and BIST registers
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Return error from probe in case of invalid phy address.
This fixes the issue of uboot crash if phy is not detected.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
preboot macro load the uEnv.txt from mmc 0 when bootmode is mmc. uenvcmd is
executed after load of uEnv.txt if it is defined in the uEnv.txt env text
file.
The default importbootenv macro reads the uEnv.txt from mmc.
Additional to this, usb_loadbootenv is added to support loading uEnv.txt
from usb dev 0.
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read information about memory from DT. This patch simplify life with
synchronization between DT and board files.
dram_init() only needs maximum RAM size below 4GB that's why please sort
banks in memory node.
dram_init_banksize() copies memory setup to bi_dram[].
This will avoid reading information from DT twice.
Memory test start/end were changed to DDR location to let memtest still
compiled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This option enable adding new platform suport just by adding defconfig
and DTS file which will target generic configuration for SoC.
Make no sense to extend Kconfig just create a pointer between DTS and
configuration file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read information about timer and interrupts from DT. This is the first
small step to move timer and intc to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is incorrect setting for USB which didn't work with origin
ps7_init_gpl.X files.
Use default setting for Digilent Zybo projects with HDMI in PL.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zybo has on board I2C EEPROM which contains preprogrammed MAC address.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass appropriate interface type to phy_connect
instead of zero.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of Xilinx PCS/PMA core phy for Zynq
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sriram Dash
Hans de Goede
Mateusz Kulikowski
Purna Chandra Mandal
Tom Rini
mario.six@gdsys.cc
York Sun
Codrin Ciubotariu
Qianyu Gong
Wenbin Song
Vincent Siles
Ed Swarthout
Shaohui Xie
Peng Fan
Chris Packham
Stefan Roese
Michal Simek
Siva Durga Prasad Paladugu
Michal Simek
Soren Brinkmann
Joe Hershberger