Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Add minimal support (only boot from mmc device) for the Congatec
Conga-QEVAl Evaluation Carrier Board with conga-Qmx6q (i.MX6 Quad
processor) module.
Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
VF610TWR is a board based on Vybrid VF610 SoC.
This patch adds basic support for Vybrid VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Currently the cm-t35 support code lives under board/cm_t35 directory.
Some of the code can be shared with other/future CompuLab boards,
so move the cm-t35 to live under board/compulab/cm_t35 directory.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
The IGEP COM AQUILA and CYGNUS are industrial processors modules with
following highlights:
o AM3352/AM3354 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add basic support for the DENX M53EVK board. Currently supported is:
MMC (incl. booting)
NAND (incl. booting)
Ethernet, I2C, USB, SATA, RTC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Titanium is a i.MX6 based board from ProjectionDesign / Barco. This
patch adds support for this board with the newly introduced NAND
support for i.MX6.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds the fast booting LWMON5 derivat "lcd4_lwmon5".
Its a stripped down version of the full blown lwmon5 support,
without ECC, USB, POST and some other stuff. It used the newly
introduced SPL infrastrucure for SPL from NOR flash booting
on the PPC4xx.
By setting the environment variable "boot_os" to "yes", Linux
will be started from the SPL version. If not, the "normal"
U-Boot will be started.
Signed-off-by: Stefan Roese <sr@denx.de>
Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu.
Add a Beaver build so it can begin to be differentiated, if need be.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This board is from a u-boot point of view a mixture between kmnusa and
a standard km_kirkwood board. We have our u-boot environment in the spi
NOR flash, but we have a direct connection between the kirkwood and the
piggy. A FPGA is connected via the PCIe interface. So we only have to
select the specific features in the board setup.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Introduce 'mx28evk_nand' target for saving environment variables into NAND.
The mx28evk board does not come with a NAND flash populated from the
factory. It comes with an empty slot (U23), which allows the insertion of a
48-pin TSOP flash device.
Tested with a K9LBG08U0D.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Wandboard is a development board that has two variants: one version based
on mx6 dual lite and another one based on mx6 solo.
For more details about Wandboard, please refer to: http://www.wandboard.org/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix the following build error when buildig nitrogen6s1g:
nitrogen6x.c:89:17: error: 'CONFIG_DDR_MB' undeclared (first use in
this function)
nitrogen6x.c:89:17: note: each undeclared identifier is reported only
once for each function it appears in
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds the configuration file for Snow Board and
defines the same in boards.cfg.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
Adding the build support for dra7xx_evm.
Reusing omap5_evm.h config by moving it to omap5_common.h
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Add new mpc5121e based ac14xx board and a new pinmux config
function for setting individual pinmux bit groups. This
function is used in ac14xx board code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds the a4m2k MPC5200B board port. Its a derivate of
the a3m071 board with only minor changes.
Additionally this patch includes some clean-up changes:
- Remove I2C support from a3m071 as its unused
- Fix/enhance default env variables
- Fix some comments
- Add newly introduced CONFIG_SPL_TARGET to automatically build
"u-boot-img.bin"
- Fix dtb patching in READ desciption for SPL Linux booting:
"fdt chosen" needs to get called to patch/create the chosen node.
- Add missing call to spl_board_init():
Define CONFIG_SPL_BOARD_INIT so that spl_board_init() will get
called in the SPL version.
Signed-off-by: Stefan Roese <sr@denx.de>
We add USB (RNDIS gadget) SPL support as a separate target. We need to
pull out YMODEM support in order to be a small enough target binary.
Signed-off-by: Tom Rini <trini@ti.com>
Board and config header files for bf609-ezkit support.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Add at91sam9g20_2mmc nand boot support. on this board, there is no
dataflash, so disable it
change one commet for at91sam9g20ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This target will move the environment into SPI flash and documents
the expected layout. We correct the SPL define for where U-Boot is
and remove an unused define.
Signed-off-by: Tom Rini <trini@ti.com>
The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This board is similar to TUXX1 but it has a different sized second
FPGA. Therefore the configuration for the third chipselect is different.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This is a preparation for the upcoming kmopti2 board. This board has
also a second fpga on board which is different to the tuxx1 target. But we
want to use the same header file. So remove the config option
KM_DISABLE_APP2 and simply use the board names to distinguish the features.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
Signed-off-by: Tom Warren <twarren@nvidia.com>
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD
Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI
Not yet supported:
NAND
RTC
LCD
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.
So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.
This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
BSC9132QDS Overview
--------------------
2Gbyte DDR3 (on board DDR), Dual Ranki
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
USB-ULPI
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
PCIe
CPRI
SerDes
I2C RTC
DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.
B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
configuration reset source. The RCW source is set by appropriate
DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
- total four refclk, including CPRI clock scheme
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The following features are supported:
* 128 MB DDR1 SDRAM
* DUART
* SD/MMC Card Socket
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds support for MX23-based Olinuxino board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
include/configs/tegra-common.h now holds common config options
for Tegra SoCs.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add dataflash boot support on at91sam9x5ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* By a sequence of unfavorable conditions in the config header file, the eb_cpu5282
booting from internal stopped after relocation. Blame it is a faulty value of
CONFIG_SYS_MONITOR_BASE. This patch fix this by replace the wrong condition in
config header with option in board.cfg
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Because calculate_relocation_address now uses the e820 map, it will be able
to avoid addresses over 32 bits and regions that are at high addresses but
not big enough for U-Boot. It also means we can remove the hack which
limitted U-Boot's idea of the size of memory to less than 4GB.
Also take into account the space needed for the heap and stack, so we avoid
picking a very small region those areas might overlap with something it
shouldn't.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tapani Utriainen
SARTRE Leo
Alison Wang
Igor Grinberg
Enric Balletbo i Serra
Marek Vasut
Matthew McClintock
Stefan Roese
Fabio Estevam
Tom Warren
Holger Brunck
Benoît Thébaudeau
SRICHARAN R
Matt Porter
Eric Nelson
Rajeshwari Shinde
Lokesh Vutla
Anatolij Gustschin
Tom Rini
Sonic Zhang
Bo Shen
Simon Glass
Tom Warren
Lars Poeschel
Javier Martinez Canillas
Michal Simek
Prabhakar Kushwaha
York Sun
Otavio Salvador
Albert ARIBAUD
Yoshihiro Shimoda
Scott Wood
Jens Scharsig (BuS Elektronik)
Gabe Black
Timur Tabi
Wu, Josh